Lamborghini Caloreclima IDOLA M 3.2 22T User Manual (English)

Questions and Answers:

E
Erica TranAug 16, 2025
Why is my Lamborghini Caloreclima Heat Pump not heating or cooling properly?
- M
  michaeldavisAug 16, 2025
  If your Lamborghini Caloreclima Heat Pump is on but not heating or cooling as expected, first, check the temperature settings on the controller (T4HMAX, T4HMIN in heat mode; T4CMAX, T4CMIN in cool mode; T4DHWMAX, T4DHWMIN in DHW mode). Also, ensure that all water circuit shut-off valves are fully open and that the water filter is clean. Purge any air from the system, verify sufficient water pressure (above 1 bar when cold), and confirm the expansion vessel isn't broken. Finally, make sure the water circuit resistance isn't too high for the pump.
R
Ryan VargasAug 19, 2025
What to do if Lamborghini Caloreclima Heat Pump stops in DHW mode before reaching setpoint?
- J
  Jamie SmithAug 19, 2025
  If your Lamborghini Caloreclima Heat Pump's DHW mode stops before reaching the setpoint and space heating requires heat, it could be due to an undersized coil in the tank. Refer to the solution for Symptom 7. Alternatively, if a TBH or AHS is unavailable, the heat pump will remain in DHW mode until "t_DHWHP_MAX" is reached or the setpoint is achieved. Consider adding a TBH or AHS for DHW mode, ensuring they are controlled by the unit.
R
rmccannAug 22, 2025
Why is my Lamborghini Caloreclima Heat Pump making noise?
- M
  Mary WilliamsAug 22, 2025
  If your Lamborghini Caloreclima Heat Pump is making noise (cavitation), it might be due to air in the system. Try purging the air. Alternatively, the water pressure at the pump inlet may be too low. Check the manometer to ensure sufficient water pressure (greater than 1 bar when the water is cold). Also, check that the manometer isn't broken and the expansion vessel is intact. Ensure the pre-pressure setting of the expansion vessel is correct (refer to "9.3 water piping/Checking the water volume and expansion vessel pre- pressure").
C
Christina SilvaAug 28, 2025
Lamborghini Caloreclima Heat Pump: Heat mode can’t change to DHW mode immediately, why?
- A
  Anthony WilliamsAug 28, 2025
  If your Lamborghini Caloreclima Heat Pump doesn't switch from heat mode to DHW mode immediately, adjust these settings: set “dT1S5” to 20°C, “t_DHWHP_RESTRICT” to the minimum value, and dT1SH to 2°C. Enable TBH, ensuring it's controlled by the outdoor unit. If a boiler (AHS) is available, turn it on first; if the requirements for the heat pump are met, it will then turn on. If neither TBH nor AHS is available, try repositioning the T5 probe (refer to 2 General information/Domestic hot water tank).
C
Colleen WallaceAug 31, 2025
Why is my Lamborghini Caloreclima Heat Pump compressor not starting?
- C
  Catherine GrayAug 31, 2025
  If your Lamborghini Caloreclima Heat Pump is on but the compressor isn't starting for space or domestic water heating, the unit might be starting outside of its operation range due to low water temperature. The system should use the backup heater to reach a minimum water temperature of 12°C. Ensure the backup heater power supply is correct, the thermal fuse is closed, the thermal protector isn't activated, and the contactors aren't broken.
D
Danielle RichardsonSep 3, 2025
Why is there space heating capacity shortage at low outdoor temperatures with Lamborghini Caloreclima Heat Pump?
- R
  Randall GuerraSep 3, 2025
  If your Lamborghini Caloreclima Heat Pump experiences space heating capacity shortage at low outdoor temperatures, verify that the "OTHER HEATING SOURCE/ BACKUP HEATER" is enabled (see "10.7 Field settings”). Check if the backup heater's thermal protector has been activated (refer to "Controls parts for backup heater (IBH) "). Also, ensure that the booster heater isn't running simultaneously with the backup heater. If too much heat pump capacity is being used for domestic hot water (if applicable), check that the “t_DHWHP_MAX” and “t_DHWHP_RESTRICT” settings are configured correctly. Disable “DHW PRIORITY” in the user interface and enable “T4_TBH_ON” in the user interface/FOR SERVICEMAN to activate the booster heater for domestic water heating.
D
Donald Jordan MDSep 6, 2025
Why does the water pressure relief valve open on my Lamborghini Caloreclima Heat Pump?
- A
  Ashley SmithSep 6, 2025
  If the water pressure relief valve on your Lamborghini Caloreclima Heat Pump opens, it could be due to a broken expansion vessel. In this case, replace the expansion vessel. Alternatively, the filling water pressure in the installation might be higher than 0.3MPa. Ensure it's about 0.15~0.20MPa (refer to "9.3 water piping/Checking the water volume and expansion vessel pre-pressure").
G
Glenn SmithSep 9, 2025
What to do if Lamborghini Caloreclima Heat Pump water pressure relief valve leaks?
- P
  pattersonsherrySep 9, 2025
  If the water pressure relief valve on your Lamborghini Caloreclima Heat Pump is leaking, dirt may be blocking the valve outlet. Check the pressure relief valve by turning the red knob counter-clockwise: if you don't hear a clacking sound, contact your local dealer. If water continues to run out, close both the water inlet and outlet shut-off valves and then contact your local dealer.
S
Sarah PetersonSep 12, 2025
What to do if Lamborghini Caloreclima Heat Pump is not heating or cooling and the water volume is too low?
- V
  Victoria GraySep 12, 2025
  If the Lamborghini Caloreclima Heat Pump is not heating or cooling as expected, ensure that the water volume in the installation is above the minimum required value (refer to "9.3 water piping/ Checking the water volume and expansion vessel pre- pressure").

Lamborghini Caloreclima IDOLA M 3.2 22T Specifications

General

Brand	Lamborghini Caloreclima
Model	IDOLA M 3.2 22T
Category	Heat Pump
Language	English

Lamborghini Caloreclima IDOLA M 3.2 22T User Manual

Table of Contents

Questions and Answers:

Lamborghini Caloreclima IDOLA M 3.2 22T Specifications