Lantronix EMG 8500 Quick Start Guide

2
5. RUN QUICK SETUP TO CONFIGURE NETWORK (IP) SETTINGS
© 2019 Lantronix, Inc. Lantronix is a registered trademark, and EMG is a trademark of Lantronix, Inc. All other trademarks are the
property of respecve owners. Specicaons subject to change without noce. 895-0004-00
Contact Technical Support
For technical support queries, visit hp://www.lantronix.com/support or call (800) 422-7044 Monday – Friday from 6:00 a.m. – 5:00 p.m.,
Pacic Time, excluding holidays.
Latest Firmware For the latest rmware downloads, visit hp://www.lantronix.com/support/downloads
6. LOGGING IN TO THE WEB PAGE
To set up the network connecons, you may do one of the following:
 Complete the Quick Setup on the Web Manager.
 SSH to the command line interface and follow the Quick Setup
script
 Connect a terminal to the console (RS-232) port and follow the
Quick Setup script on the command line interface
The Quick Setup script lets you congure the Eth1 network sengs,
change the date and me, and change the sysadmin password.
Aer you save the values for your EMG, the changes take eect
immediately.
7. LOGGING IN TO THE COMMAND INTERFACE
You can use either the Web Manager or the command line interface to
congure all parameters.
To log in to the EMG 8500 web page:
1. Open a web browser (Firefox, Chrome, Safari, or Internet Explorer
with the latest browser updates).
2. In the URL eld, type hps:// followed by the IP address of your
EMG.
3. At the rst login, enter sysadmin (all lower case) as the user and
PASS (all upper case) as the factory default password.
Note: Change the default password as soon as possible to prevent
access by unauthorized personnel.
The rst me you log in, the EMG 8500 Quick Setup page is displayed.
Subsequent logins will display the EMG 8500 Home Page.
To access the command line interface:
1. Do one of the following:
• With a network connecon, use a Telnet or SSH program to Telnet or
SSH to xx.xx.xx.xx (the IP address in dot quad notaon), and press
Enter. You should be at the login prompt.
Note: By default, Telnet is disabled. To enable it, use the Services web
page, a serial terminal connecon, or an SSH connecon with a serial
terminal connecon. When the command line displays, press Enter.
2. Enter sysadmin as the user name and press Enter.
3. Enter PASS as the password and press Enter. The rst me you log in,
the Quick Setup script opens automacally. Subsequent logins display
the command prompt only.
Note: Change the default password as soon as possible to prevent access
by unauthorized personnel.
4. If the Quick Setup script displays, update basic network parameters, as
desired. Otherwise, just press Enter unl the command prompt dis-
plays. By pressing Enter, you are accepng the current sengs.
Notes: For general command line interface help, type “help command
line”.
For help with a specic command, type “help” followed by the command;
for example, “help set network” or “help admin rmware”.
4. IP ADDRESSING
Both of the EMG 8500 network ports (Ethernet 1 and Ethernet 2) de-
fault to DHCP–assigned IP addresses. If you want to assign a dierent IP
address, it must be within a valid range, unique to your network, and
use the same subnet mask as your workstaon.
To congure the EMG 8500, you need the following informaon:
IP address (if not already assigned): ______ . ______ . ______ . ______
Subnet mask (if not already assigned): ______ . ______ . ______ . ______
Gateway: ______ . ______ . ______ . ______
DNS: ______ . ______ . ______ . ______
EMG
™
8500 Quick Start Guide
Edge Management
Gateway
Note: To access the web page or to access the command line interface
using SSH or Telnet, the EMG unit must have a network connecon and IP
address.
Note: You can view the IP address by running the Lantronix Provisioning
Manager (LPM) applicaon. Download LPM from here and follow
instrucons in the user guide to discover devices.
4. Do one of the following:
• To bypass the Quick Setup page and go directly to conguring the
EMG, click the Accept default Quick Setup sengs checkbox and click
Apply.
• Update the basic network parameters, if desired, and click Apply.
Aer you save the values for the EMG unit, the changes take eect
immediately.

Lantronix EMG 8500 Specifications

General

Brand	Lantronix
Model	EMG 8500
Category	Gateway
Language	English