Lantronix SGX 5150 Command Reference

3: Command Line Interface
SGX 5150 IoT Device Gateway Command Reference 11
TM
To configure the SGX 5150 IoT device gateway locally using a serial port:
1. Connect a terminal or a PC running a terminal emulation program to one of the gateway's
serial ports.
2. Configure the terminal to the following settings:
 9600 baud
 8-bit
 No parity
 1 stop bit
 No flow control.
3. Power off the gateway.
4. Press and hold down the exclamation point (!) key.
5. Power on the gateway. After about 10 seconds, the exclamation point will display on the
terminal or PC screen.
6. Type xyz within 5 seconds to display the CLI prompt.
Navigating the CLI Hierarchy
The CLI is organized into a hierarchy of levels. Each level has a group of commands for a specific
purpose. For example, to configure a setting for the FTP server, one would navigate to the FTP
level, which is under the configuration level.
 To move to a different level—Enter the name of the level from within its parent level. For
example, to enter the line level, type line <number> at the enable prompt. This displays:
<enable> line <number>#.
 To exit and return to one level higher—Type exit and press the Enter key. Typing exit at
the login level or the enable level will close the CLI session.
 To view the current configuration at any level—Type show.
 To view the list of commands available at the current level—Type the question mark "?". Items
within < > (e.g. <string>) are required parameters.
 To view the available commands and explanations—Type the asterisk (*).
 To view the list of commands available for a partial command—Type the partial command
followed by the question mark "?". For example: <line 1>#show? displays a list of all show
commands at the line level.
 To view available commands and their explanations for a partial command—Type the partial
command followed by the asterisk (*). For example: <line 1>#show* displays a list of all
show commands and descriptions at the line level.
 To view the last 20 commands entered at the CLI—Type show history.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm