Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 256
protocol tcp aes
Uses TCP protocol with AES encryption for connect mode tunneling.
protocol telnet
Uses Telnet protocol (with IAC) for connect mode tunneling.
protocol udp
Uses UDP protocol for connect mode tunneling.
protocol udp aes
Uses UDP protocol with AES encryption for connect mode tunneling.
secure protocols ssl3
disable
Disables the protocol.
secure protocols ssl3
enable
Enables the protocol.
secure protocols tls1.0
disable
Disables the protocol.
secure protocols tls1.0
enable
Enables the protocol.
secure protocols tls1.1
disable
Disables the protocol.
secure protocols tls1.1
enable
Enables the protocol.
secure protocols tls1.2
disable
Disables the protocol.
secure protocols tls1.2
enable
Enables the protocol.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show statistics
show connection statistics
ssh username <text>
Sets the SSH user name for use when establishing tunneling connections with other devic-
es. <text> = SSH user name.
tcp keep alive <millisec-
onds>
Sets the TCP keep alive idle time. This is the initial keep alive timeout. <milliseconds> =
timer value, in milliseconds.
tcp keep alive interval
<milliseconds>
Enables TCP keep alive for connect mode tunneling and sets the timer. <milliseconds> =
TCP keep alive for connect mode in milliseconds.
tcp keep alive probes
<number>
Sets the number of TCP keep alive probes. <number> = number of TCP keep alive probes.
tcp user timeout <milli-
seconds>
Sets the timeout for TCP retransmissions. <milliseconds> = timeout value, in milliseconds.
validate certificate disa-
ble
Skips verification of the server certificate when connecting.
validate certificate enable
Requires verification of the server certificate when connecting.
write
Stores the current configuration in permanent memory.
host 4 (config-host:4) level commands
clrscrn
Clears the screen.
default protocol
Restores the default value of the protocol (Telnet).
default remote port
Sets the remote port (used to connect to the host) to the default value, which depends on
the selected protocol.
exit
Exits to the configuration level.
host <number>
Change to config host level
name <text>
Sets the name of the host. <text> = name of the host.
no name
Clears the name of the host.
no remote address
Clears the remote address of the host.
no ssh username
Clears the SSH username associated with the host.
protocol ssh
Sets the protocol to SSH.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm