Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 297
notation. A network is denoted by the first address in the block (ending in all zeroes), a
slash (/), and a decimal value equal to the size in bits of the prefix
ipv6 state enable
Enables IPv6 for the interface.
link
Enter link configuration level
mtu <bytes>
Sets the Maximum Transmission Unit (MTU) size.
no default gateway
Clears the default gateway.
no dhcp client id
Clears the DHCP client ID.
no domain
Clears the domain name.
no hostname
Clears the host name.
no ip address
Clears the IP address.
no ipv6 address
Clears the IPv6 static address.
no ipv6 default gateway
Clears the IPv6 default gateway.
no ipv6 domain
Clears the IPv6 domain name.
no ipv6 primary dns
Clears the IPv6 address of the primary DNS server.
no ipv6 secondary dns
Clears the IPv6 address of the secondary DNS server.
no primary dns
Clears the name of the primary DNS server.
no secondary dns
Clears the name of the secondary DNS server.
primary dns <IP ad-
dress>
Sets the IP address of the primary DNS server.
priority <number>
Sets the priority for interface. <number> = priority number.
qos
Enter QoS configuration level
secondary dns <IP ad-
dress>
Sets the IP address of the secondary DNS server.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Show interface status
state disable
Disables the interface.
state enable
Enables the interface.
write
Stores the current configuration in permanent memory.
if 3 (config-if:usb0) level commands
clrscrn
Clears the screen.
default gateway <IP ad-
dress>
Sets the configurable gateway IP address to the default value.
default mtu
Restores the default Maximum Transmission Unit (MTU) size.
default priority
Restores the default priority for the interface.
dhcp client id <text>
Sets the DHCP client ID.
dhcp disable
Disables DHCP.
dhcp enable
Enables DHCP.
dhcp renew
Force DHCP to renew
domain <text>
Sets the domain name. <text> = name of the domain.
exit
Exits to the config level.
failover
Enter failover configuration level
hostname <text>
Sets the host name. <text> = name of the host.
if <instance>
Changes to the interface configuration level.
ip address <ip ad-
dress/cidr>
Sets the IP address and network mask. Formats accepted: 192.168.1.1 (default mask)
192.168.1.1/24 (CIDR) "192.168.1.1 255.255.255.0" (explicit mask)

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm