Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 360
no privacy password
Clears privacy password for traps.
no secondary destination
Deletes the secondary SNMP trap host.
no username
Clears SNMPv3 username for traps.
primary destination
<text>
Sets the primary SNMP trap host. <text> = IP address or hostname of SNMP trap receiver.
primary destination port
<number>
Sets the primary SNMP trap host port.
privacy password <text>
Sets password used for privacy encryption for traps.
privacy protocol aes
Uses AES for privacy encryption for traps.
privacy protocol des
Uses DES for privacy encryption for traps.
secondary destination
<text>
Sets the secondary SNMP trap host. <text> = IP address or hostname of SNMP trap re-
ceiver.
secondary destination
port <number>
Sets the secondary SNMP trap host port.
security authentication
and privacy
Authentication and Privacy for traps.
security authentication
but no privacy
Authentication, No Privacy for traps.
security no authentication
and no priv
No Authentication, No Privacy for traps.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
username <text>
Sets SNMPv3 username for traps.
version snmpv1
Uses SNMPv1 for traps.
version snmpv2c
Uses SNMPv2c for traps.
version snmpv3
Uses SNMPv3 for traps.
write
Stores the current configuration in permanent memory.
trusted authorities (ssl-auth) level commands
add
Adds an Authority Certificate.
clrscrn
Clears the screen.
exit
Exits to the ssl level.
no intermediate authority
<cert>
Removes an Intermediate Authority Certificate. <cert> = index displayed by "show authori-
ty" command.
no trusted authority
<cert>
Removes a Trusted Authority Certificate. <cert> = index displayed by "show authority"
command.
show
Displays Authority Certificate Information.
show history
Displays the last 20 commands entered during the current CLI session.
write
Stores the current configuration in permanent memory.
tunnel 1 (tunnel:1) level commands
accept
Enters the accept level for this tunnel.
auto show statistics
show connection statistics
bluetooth serial <line>
Enters the bluetooth serial level. <line> = number of the line (bluetooth serial port) to be
configured.
clear counters
Zeros all tunnel counters
clrscrn
Clears the screen.
connect
Enters the connect level for this tunnel.
disconnect
Enters the disconnect level for this tunnel.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm