Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 66
clrscrn
Clears the screen.
credentials <text>
Selects the RSA/DSA certificates by name for the SSL server.
default accept mode
Restores the default accept mode as 'always'.
default local port
Uses the default port number as the local port for accept mode tunneling. The default port
is 10000 + n, where 'n' is the line number for this tunnel.
default protocol
Restores the default accept mode tunneling protocol as 'TCP'.
default start character
Defaults the accept mode start character.
default tcp keep alive
Defaults the TCP keep alive time.
default tcp keep alive
interval
Restores the default 45 second accept mode TCP keep alive timeout.
default tcp keep alive
probes
Defaults the TCP keep alive probes.
email connect <number>
Sets an email profile to use to send an email alert upon establishing an accept mode tun-
nel. <number> = the number of the email profile to use.
email disconnect <num-
ber>
Sets an email profile to use to send an email alert upon closing an accept mode tunnel.
<number> = the number of the email profile to use.
exit
Returns to the tunnel level.
flush serial disable
Characters already in the serial data buffer are retained upon establishing an accept mode
tunneling connection.
flush serial enable
Flushes the serial data buffer upon establishing an accept mode tunneling connection.
flush start character dis-
able
Enables forwarding of the accept start character into the network.
flush start character ena-
ble
Disables forwarding of the accept start character into the network.
initial send binary <bina-
ry>
Sets the accept tunnel Initial Send text allowing for binary characters. <binary> = string in
binary format that will be sent out the network upon connection. Within [] use binary deci-
mal up to 255 or hex up to 0xFF.
initial send set <text>
Sets the accept tunnel Initial Send text. <text> = ascii string that will be sent out the net-
work upon connection.
kill connection
Disconnects the active accept mode tunneling connection.
local port <number>
Sets the port to use for accept mode tunneling. <number> = number of the port to use.
no aes decrypt key
Removes the accept tunnel AES decrypt key.
no aes encrypt key
Removes the accept tunnel AES encrypt key.
no credentials
Clears the RSA/DSA certificate selection for the SSL server.
no email connect
Discontinues sending email alerts upon establishing an accept mode tunnel.
no email disconnect
Discontinues sending email alerts upon closing an accept mode tunnel.
no initial send
Removes the accept tunnel Initial Send string.
password
Enters the next lower level.
protocol ssh
Uses SSH protocol for accept mode tunneling.
protocol ssl
Uses SSL protocol for accept mode tunneling.
protocol tcp
Uses TCP protocol for accept mode tunneling.
protocol tcp aes
Uses TCP protocol with AES encryption for accept mode tunneling.
protocol telnet
Uses Telnet protocol (with IAC) for accept mode tunneling.
secure protocols ssl3
disable
Disables the protocol.
secure protocols ssl3
enable
Enables the protocol.
secure protocols tls1.0
Disables the protocol.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm