Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 81
bridge <instance>
Changes to the bridge configuration level.
cli
Change to menu level for CLI configuration and status
clock
Change to menu level for Clock configuration and status
clrscrn
Clears the screen.
diagnostics
Enters the diagnostics level.
discovery
Enters the discovery level.
exit
Exits to the enable level.
ftp
Enters the ftp level.
gateway
Enters the gateway level.
gre <instance>
Change to gre level.
host <number>
Change to config host level
http
Enters the http level.
icmp
Changes to the command level for ICMP configuration and status.
if <instance>
Changes to the interface configuration level.
ip
Changes to the command level for IP configuration and status.
kill ssh <session>
Kills SSH session with index from "show sessions"
kill telnet <session>
Kills Telnet session with index from "show sessions"
mach10
Enters the mach10 level.
modbus
Changes to the modbus configuration level.
rss
Change to menu level for RSS configuration and status
security
Enters the security level.
sftp
Enters the sftp level.
show
Displays system information.
show history
Displays the last 20 commands entered during the current CLI session.
show lines
Displays line information.
smtp
Changes to the command level for SMTP configuration and status.
snmp
Enters the snmp level.
syslog
Enters the syslog level.
terminal <line>
Enters the configure-terminal level. <line> = number of the terminal line (serial port) to be
configured.
terminal network
Enters the configure-terminal level for the network.
user management
Enters the config-user-management level.
vpn <instance>
Change to vpn level.
wlan profiles
Enters the WLAN profiles configuration level.
write
Stores the current configuration in permanent memory.
connect (tunnel-connect:4) level commands
block network disable
Forwards (tunnels) network data in connect mode tunneling.
block network enable
Discards all data coming in from the connect mode tunnel before forwarding it to the serial
interface (generally used for debugging).
block serial disable
Forwards (tunnels) serial data in connect mode tunneling.
block serial enable
Discards all data coming in from the serial interface before forwarding it to the connect
mode tunnel (generally used for debugging).
clrscrn
Clears the screen.
connect mode always
Enables the tunneling server to always establish tunneling connections.
connect mode any char-
acter
Enables the tunneling server to establish a tunneling connection when a character is re-
ceived on the corresponding line (serial port).

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm