Need help?Do you have a question about the Leica PRADOVIT RT-s and is the answer not in the manual?
General| Type | Slide projector |
|---|---|
| Lamp Type | Halogen |
| Compatibility | 35mm slides |
| Weight | 5.5 kg |
| Focal Length | Varies depending on lens |
| Aperture | Varies depending on lens |
| Light Source | 24V 250W halogen lamp |
| Projection Distance | Varies depending on lens |
Explains how to navigate and utilize the instruction manual for optimal projector operation.
Essential safety guidelines for operating the projector, including handling and environmental considerations.
Instructions on verifying and setting the correct mains voltage for projector operation before connection.
Steps for powering on the projector after setting the correct operating voltage.
Guidance on how to correctly attach the projector lens to the unit for optimal image projection.
Instructions on how to securely mount the projector onto a stable surface or stand.
How to select and set the correct tray type (80 or 140 slides) for the projector.
Explains the line-up feature for aligning projectors in multi-vision setups.
Step-by-step guide for manually adjusting image focus using projector or remote control buttons.
How to use the override function to manually adjust focus even when autofocus is active.
Instructions for faster tray movement to desired slides, bypassing slot insertion.
How to set automatic slide show timings with the built-in timer for continuous projection.
Programming automatic slide shows using the IR remote control's auto-timer feature.
How to interrupt and resume slide presentations using the stand-by function.
How to set the lamp to economy mode for extended life and reduced brightness.
How to set the projector lamp to its normal operating brightness.
Instructions for connecting the projector to a PC for direct control via P-COM protocol.
Step-by-step guide on how to safely replace a faulty projector lamp.
How to choose between different operating modes like priority lamp or random access.
Details on additional functions available with the remote controls, such as random access.
How to set up and operate multiple projectors in a parallel projection configuration.
Advanced instructions for controlling the projector via computer using the P-COM protocol.
Basic guidelines for operating the remote controls, including range and aiming.
Critical safety warnings regarding the use of the laser pointer on the IR remote control.
Instructions on how to connect the cable remote control or IR receiver to the projector.
Explains how to select specific slides directly using the remote control.
How to initiate a basic dissolve projection with a preset speed of 0.5 seconds.
How to pause the slide show at any point, freezing the current image.
Guides on setting up and configuring two projectors for simultaneous projection.
Steps for connecting and configuring two projectors for dissolve or multi-vision presentations.
Detailed steps for precisely aligning projector images for overlap using setting slides.
Instructions for organizing slides into the correct trays for MASTER and SLAVE projectors.
Guide on programming dissolve transition durations using IR remote codes.
How to select specific slides directly using the remote control, including in the zero compartment.
Exploring advanced control options such as fade commands and lamp status adjustments.
Using the 'Alternate' command to switch between projector lamp statuses without slide movement.
Instructions for programming and executing parallel projection with multiple projectors.
How to revert to the basic dissolve setting for two-projector setups using a specific code.
How to configure the remote control for presentation mode, restricting functions to single steps.
How to reset the projector to its zero position, equivalent to power cycling.
Step-by-step guide on how to safely replace a faulty projector lamp.
Instructions for replacing the fuse in the projector's primary circuit.
How to replace the fuses protecting the secondary circuit from excess current.
Detailed steps for safely removing and installing the projector's condenser unit.
Safety precautions and instructions for cleaning the projector's exterior and optical elements.
Overview of optional accessories available for the projector, including lenses.
Description and order number for the special condenser for 4x4 Superslides.
Details on the IR remote control, its functions, and compatibility with projectors.
Key technical details of the projector, including dimensions, power, and fuses.
Information on different lamp modes (economy, high-light) and operating temperature limits.
Specific measurements, weight, and lens mount details for the projector.
Detailed pinout for the module slot and projector remote control connector.
Contact details for service, repairs, and technical assistance from Leica.
Addresses issues where the projector is unresponsive or in silent mode without apparent defects.
Covers problems related to fitting, moving, and correctly positioning the slide tray.
Details problems with image focus and potential solutions.
Solutions for projector startup failures and silent mode issues.
Addresses problems with dim lamps, fan operation, and ventilation.
Solutions for tray cycling problems and issues with timer/zeroing controls.
Guidance on resolving issues related to dim lamps, condenser placement, and image focus.
To Next Page
