Lenze 9300 vector - Page 463

Appendix
Index
14
14.2

14.2−6
EDSVF9383V EN 6.0−11/2009
Rated motor speed, 6.6−1 , 6.6−17 , 6.8−9 , 8.2−29 ,
8.2−44 , 8.5−9
Rated motor voltage, 6.6−2 , 6.6−17 , 6.8−5 , 6.8−9 ,
8.2−29 , 8.2−44 , 8.5−9
Reaction times of digital inputs, 6.5−1
Relay output, Configuration, 6.5−3
Residual hazards, 2.3−1
Responses, 8.3−1
− message, 8.3−1
− TRIP, 8.3−1
− warning, 8.3−1
Running optimisation, 6.11−1
S
Safe standstill, 11.1−1
Safe torque off, 11.1−1
− Function deactivated, 5.5−7
− functional test, 11.4−2 , 11.4−5
− operating mode, 11.2−2
− safety relay, 3.4−1 , 11.3−1
Safe torque offt, Function active, 5.5−4
Safety, safety engineering, 11−1
Safety engineering, 11−1
Safety function
− functional test, 11.4−2 , 11.4−5
− Safe torque off, 11.1−1
Safety instructions, 2−1
− definition, 1.4−1
− layout, 1.4−1
Safety relay, 3.4−1 , 11.3−1
− Connector X11
Terminal assignment, 11.3−2
Wiring, 11.3−2
Safety relay KSR, Terminal assignment, 5.5−9 , 11.3−2
Selecting the operating mode, speed mode, setting
acceleration and deceleration times, 6.10−3
Selection, operating mode, 6.1−1 , 6.8−1
Selection of motor type, 6.6−1 , 8.2−29 , 8.2−44 , 8.5−9
Selection of the feedback system, 6.7−1 , 8.2−42 , 8.5−4
Setting integral action component, 8.2−49
Setting the acceleration time, 6.10−3
Setting the deceleration time, 6.10−3
Setting the feedback system, 6.7−1
Setting the speed feedback, 6.7−1
Shielding
− DC−bus cable, 5.3−5 , 5.4−9
− motor cable, 5.3−7 , 5.4−12
Site altitude, 3.1−2
Slip compensation, 6.11−1 , 8.2−39 , 8.2−61
Speed control, 8.2−31 , 8.2−48
− adapting the speed controller, 8.2−48
− at vector control (MCTRL2), adapting the speed
controller, 8.2−31
− with vector control (MCTRL2)
setting integral action component, 8.2−49
speed feedback, 8.2−48
temperature detection, 8.2−49
Speed feedback, 8.2−48
Speed mode, setting acceleration and deceleration
times, 6.10−3
Speed oscillations, 6.11−3
Speed setpoint limitation, 8.2−31 , 8.2−47
Speed setpoint selection, 8.2−31 , 8.2−47
Stability, of the motor, 8.2−50
Status word AIF, 8.5−14 , 9.1−2
Stopping, 6.10−1
Supply forms / electrical supply conditions, 5.1−4
Switching frequency, automatic current−dependent
change−over, 6.9−2 , 8.2−27 , 8.2−41 , 8.5−4
Switching frequency of inverter, 6.9−1
− noise optimised, 6.9−1
Switching frequency reduction, 6.9−2
switching on, check before switching on, 6.1−1
System bus (CAN), wiring, 5.6−1
System error messages, 9.5−1
− configuration, 8.4−1
− General, 9.5−1
− Resetting, 9.5−5
T
Table of attributes, 8.7−1
Technical data, 3−1
Temperature detection, 8.2−49
Terminal assignment
− analog inputs, 5.5−9
− analog outputs, 5.5−9
− digital inputs, 5.5−9
− Digital inputs/outputs, 11.3−2
− digital outputs, 5.5−9
− Safety relay KSR, 5.5−9 , 11.3−2
efesotomasyon.com - Lenze