Lenze i410 - Page 210

Address Name / seng range / [default seng] Informaon
0x2637:002
(P431.02)
Analog input 2: Min frequency value
(Analog input 2: AI2 fr
eq @ min)
-1000.0 ... [0.0] ... 1000.0 Hz
Scaling of the input signal to the frequency value.
•
Direcon of rotaon according to sign.
•
The standard setpoint source for operang mode 0x6060 (P301.00) =
"MS: Velocity mode [-2]" is selected in 0x2860:001 (P201.01).
4
Conguring the frequency control ^ 64
0x2637:003
(P431.03)
Analog input 2: Max frequency value
(Analog input 2: AI2 fr
eq @ max)
Device for 50-Hz mains: -1000.0 ... [50.0] ... 1000.0 Hz
Device for 60-Hz mains: -1000.0 ... [60.0] ... 1000.0 Hz
0x2637:004
(P431.04)
Analog input 2: Min PID value
(Analog input 2: AI2 PID @ min)
-300.00 ... [0.00] ... 300.00
PID unit
Scaling of the input signal to the PID value.
•
The standard setpoint source for the reference value of PID control is
selected in 0x2860:002 (P201.02).
4Conguring the process controller ^ 98
0x2637:005
(P431.05)
Analog input 2: Max PID value
(Analog input 2: AI2 PID @ ma
x)
-300.00 ... [100.00] ... 300.00 PID unit
0x2637:006
(P431.06)
Analog input 2: Filter me
(Analog input 2: AI2 lter me)
0 ... [10] ... 10000 ms
PT1 me constant for low-pass lter.
•
B
y the use of a low-pass lter, the impacts of noise to an analog signal
c
an be minimised.
•
For an opmum lter eect, rst the noise frequency has to be
determined. The me constant then has to be set so that it equals the
reciprocal value of the double frequency.
0x2637:007
(P431.07)
Analog input 2: Dead band
(Analog input 2: AI2 dead band)
0.0 ... [0.0] ... 100.0 %
Oponal seng of a dead band that is placed symmetrically around the
frequency zero point.
•
If the analog input value is within the dead band, the output value for
the motor control is set to "0".
•
100 % = maximum value of analog input (0x2636:003 (P430.03),
0x2636:005 (P430.05), 0x2636:012 (P430.12))
•
Example: Dead band 10 % of 50 Hz: -10 V … 10 V Dead band -5 Hz …
5 Hz, 0 … 10 V Dead band 0 Hz … 5 Hz
0x2637:008
(P431.08)
Analog input 2: Monitoring threshold
(Analog input 2: AI2 monit.level)
-100.0 ... [0.0] ... 100.0 %
Monitoring threshold for analog input 2.
•
100 % = 10 V (with conguraon as voltage input)
•
100 % = 20 mA (with conguraon as current loop)
Excepon: In the case of a congured input range 4...20 mA (0x2636:001
[4]), the monitoring is triggered at 2 mA with a monitoring threshold of
0.0 %.
0x2637:009
(P431.09)
Analog input 2: Monitoring condion
(Analog input 2: Monitoring cond.)
Monitoring condion for analog input 2.
•
If the select
ed condion is met, the "Error of analog input 2 acve
[82]" trigger is set to TRUE. The trigger can be assigned to a funcon
or a digital output.
•
If the selected condion is met for at least 500 ms, the error response
set in 0x2637:010 (P431.10) takes place.
0 Input value < trigger threshold
1 Input value > trigger threshold
0x2637:010
(P431.10)
Analog input 2: Error response
(Analog input 2: AI2 error resp.)
Error response for analog input 2.
•
The selected response takes place if the monitoring condion selected
in 0x2637:009 (P431.09) is met for at least 500 ms.
Associated error code:
•
28802 | 0x7082 - Analog input 2 fault
0 No response
4Err
or types ^ 285
1 Warning
2 Trouble
3 Fault
0x2637:011
(P431.11)
Analog input 2: Min torque value
(Analog input 2: Min. t
orque)
-400.0 ... [0.0] ... 400.0 %
•
From version 03.00
Scaling of the input signal to the torque value.
•
100 % = permissible maximum torque 0x6072 (P326.00)
•
Direcon of rotaon according to sign.
•
The standard setpoint source for operang mode 0x6060 (P301.00) =
"MS: Torque mode [-1]" is selected in 0x2860:003 (P201.03).
4Conguring the torque control ^ 129
0x2637:012
(P431.12)
Analog input 2: Max torque value
(Analog input 2: Max. torque)
-400.0 ... [100.0] ... 400.0 %
•
From version 03.00
I/O extensions and control connecons
Congure analog inputs
Analog input 2
210