Lenze i550 - Page 564

Display code Short designaon Default seng Seng range Address Category
└ P400.15 Setp: AI2 Not connected [0] Trigger list ^ 64 0x2631:015 general
└ P400.16 Setp: Keypad Not connected [0] Trigger list ^ 64 0x2631:016 general
└ P400.17 Setp: Network Not connected [0] Trigger list ^ 64 0x2631:017 general
└ P400.18 Setp: Preset b0 Digital input 4 [14] Trigger list ^ 64 0x2631:018 general
└ P400.19 Setp: Preset b1 Digital input 5 [15] Trigger list ^ 64 0x2631:019 general
└ P400.20 Setp: Preset b2 Not connected [0] Trigger list ^ 64 0x2631:020 general
└ P400.21 Setp: Preset b3 Not connected [0] Trigger list ^ 64 0x2631:021 general
└ P400.22 Setp: HTL input Not connected [0] Trigger list ^ 64 0x2631:022 general
└ P400.23 MOP up Not connected [0] Trigger list ^ 64 0x2631:023 general
└ P400.24 MOP down Not connected [0] Trigger list ^ 64 0x2631:024 general
└ P400.25 Setp: MOP Not connected [0] Trigger list ^ 64 0x2631:025 general
└ P400.26 Setp: Segment b0 Not connected [0] Trigger list ^ 64 0x2631:026 Sequencer
└ P400.27 Setp: Segment b1 Not connected [0] Trigger list ^ 64 0x2631:027 Sequencer
└ P400.28 Setp: Segment b2 Not connected [0] Trigger list ^ 64 0x2631:028 Sequencer
└ P400.29 Setp: Segment b3 Not connected [0] Trigger list ^ 64 0x2631:029 Sequencer
└ P400.30 Seq: Run/abort Not connected [0] Trigger list ^ 64 0x2631:030 Sequencer
└ P400.31 Seq: Start Not connected [0] Trigger list ^ 64 0x2631:031 Sequencer
└ P400.32 Seq: Next step Not connected [0] Trigger list ^ 64 0x2631:032 Sequencer
└ P400.33 Seq: Pause Not connected [0] Trigger list ^ 64 0x2631:033 Sequencer
└ P400.34 Seq: Suspense Not connected [0] Trigger list ^ 64 0x2631:034 Sequencer
└ P400.35 Seq: Stop Not connected [0] Trigger list ^ 64 0x2631:035 Sequencer
└ P400.36 Seq: Abort Not connected [0] Trigger list ^ 64 0x2631:036 Sequencer
└ P400.37 Network control Not connected [0] Trigger list ^ 64 0x2631:037 general
└ P400.39 Acv. ramp 2 Not connected [0] Trigger list ^ 64 0x2631:039 general
└ P400.40 Load param.set Not connected [0] Trigger list ^ 64 0x2631:040 general
└ P400.41 Sel. paramset b0 Not connected [0] Trigger list ^ 64 0x2631:041 general
└ P400.42 Sel. paramset b1 Not connected [0] Trigger list ^ 64 0x2631:042 general
└ P400.43 Fault 1 Not connected [0] Trigger list ^ 64 0x2631:043 general
└ P400.44 Fault 2 Not connected [0] Trigger list ^ 64 0x2631:044 general
└ P400.45 PID o Not connected [0] Trigger list ^ 64 0x2631:045 general
└ P400.46 PID output=0 Not connected [0] Trigger list ^ 64 0x2631:046 general
└ P400.47 PID-I inhibited Not connected [0] Trigger list ^ 64 0x2631:047 general
└ P400.48 PID-Inf ramp on TRUE [1] Trigger list ^ 64 0x2631:048 general
└ P400.49 Open brake Not connected [0] Trigger list ^ 64 0x2631:049 general
└ P400.50 Seq: Select. b0 Not connected [0] Trigger list ^ 64 0x2631:050 Sequencer
└ P400.51 Seq: Select. b1 Not connected [0] Trigger list ^ 64 0x2631:051 Sequencer
└ P400.52 Seq: Select. b2 Not connected [0] Trigger list ^ 64 0x2631:052 Sequencer
└ P400.53 Seq: Select. b3 Not connected [0] Trigger list ^ 64 0x2631:053 Sequencer
└ P400.54 PosCounter reset Not connected [0] Trigger list ^ 64 0x2631:054 general
└ P400.55 Acv. UPS oper. Not connected [0] Trigger list ^ 64 0x2631:055 general
P410.xx DI sengs
└ P410.01 Asseron level HIGH acve [1] Selecon list 0x2630:001 general
└ P410.02 Input funcon Digital Input [0] Selecon list 0x2630:002 general
P411.xx DI inversion
└ P411.01 DI1 inversion Not inverted [0] Selecon list 0x2632:001 general
└ P411.02 DI2 inversion Not inverted [0] Selecon list 0x2632:002 general
└ P411.03 DI3 inversion Not inverted [0] Selecon list 0x2632:003 general
└ P411.04 DI4 inversion Not inverted [0] Selecon list 0x2632:004 general
└ P411.05 DI5 inversion Not inverted [0] Selecon list 0x2632:005 general
└ P411.06 DI6 inversion Not inverted [0] Selecon list 0x2632:006 Appl. I/O
└ P411.07 DI7 inversion Not inverted [0] Selecon list 0x2632:007 Appl. I/O
P412.00 Freq. threshold 0.0 Hz 0.0 ... 599.0 Hz 0x4005 general
P413.00 MOP startmode Last value [0] Selecon list 0x4003 general
P414.xx MOP start value
* Default seng depending on the size.
Using accessories
Keypad
Keypad parameterisaon mode
564