Lenze i550 - Page 697

Address Designaon Default seng Category Data type Factor A M
0x4021:002
(P606.02)
PID speed operaon: Deceleraon me 1.0 s general U16 10 P -
0x4022:001
(P451.01)
PID setpoint presets: Preset 1 0.00 PID unit general I16 100 P -
0x4022:002
(P451.02)
PID setpoint presets: Preset 2 0.00 PID unit general I16 100 P -
0x4022:003
(P451.03)
PID setpoint presets: Preset 3 0.00 PID unit general I16 100 P -
0x4022:004
(P451.04)
PID setpoint presets: Preset 4 0.00 PID unit general I16 100 P -
0x4022:005
(P451.05)
PID setpoint presets: Preset 5 0.00 PID unit general I16 100 P -
0x4022:006
(P451.06)
PID setpoint presets: Preset 6 0.00 PID unit general I16 100 P -
0x4022:007
(P451.07)
PID setpoint presets: Preset 7 0.00 PID unit general I16 100 P -
0x4022:008
(P451.08)
PID setpoint presets: Preset 8 0.00 PID unit general I16 100 P -
0x4023:001
(P610.01)
PID sleep mode: Acvaon Disabled [0] general U8 1 P -
0x4023:002
(P610.02)
PID sleep mode: Stop method Coasng [0] general U8 1 P -
0x4023:003
(P610.03)
PID sleep mode: Frequency threshold 0.0 Hz general U16 10 P -
0x4023:004
(P610.04)
PID sleep mode: Feedback threshold 0.00 PID unit general I16 100 P -
0x4023:005
(P610.05)
PID sleep mode: Delay me 0.0 s general U16 10 P -
0x4023:006
(P610.06)
PID sleep mode: Recovery Setpoint > threshold OR
system deviaon > band-
width [0]
general U8 1 P -
0x4023:007
(P610.07)
PID sleep mode: Bandwidth 0.00 PID unit general U16 100 P -
0x4023:008
(P610.08)
PID sleep mode: Recovery threshold 0.00 PID unit general I16 100 P -
0x4024:001
(P615.01)
Automac rinsing: Rinsing in idle state Inhibited [0] general U8 1 P -
0x4024:002
(P615.02)
Automac rinsing: Rinse interval 30.0 min general U16 10 P -
0x4024:003
(P615.03)
Automac rinsing: Rinse speed 0.0 Hz general I16 10 P -
0x4024:004
(P615.04)
Automac rinsing: Rinse period 0.0 s general U16 10 P -
0x4025
(P800.00)
Sequencer mode Disabled [0] Sequencer U8 1 P -
0x4026:001
(P801.01)
Sequencer segment 1: Frequency setpoint 0.0 Hz Sequencer I16 10 P -
0x4026:002
(P801.02)
Sequencer segment 1: Acceleraon/deceleraon 5.0 s Sequencer U16 10 P -
0x4026:003
(P801.03)
Sequencer segment 1: Time 0.0 s Sequencer U32 10 P -
0x4026:004
(P801.04)
Sequencer segment 1: Digital outputs 0 Sequencer U8 1 P -
0x4026:005
(P801.05)
Sequencer segment 1: Analog outputs 0.00 VDC Sequencer U16 100 P -
0x4026:006
(P801.06)
Sequencer segment 1: PID setpoint 0.00 PID unit Sequencer I16 100 P -
0x4026:007
(P801.07)
Sequencer segment 1: Torque setpoint 100.0 % Sequencer I16 10 P -
* Default seng depending on the size.
Appendix
Parameter aribute list
697