THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
WOW_WAKE_UP
POWER_ON/OFF1
R3005 10K
MICOM_LCD/OLED
R3004 10K
OPT
I2C_SDA2
RUE003N02
Q3001
HDMI_CEC_FET_ROHM
S
D
G
+3.5V_ST
R3030
10K
R3014 10K
MICOM_DEBUG
+3.5V_ST
WOL_CTL
SCART_MUTE
KEY1
CEC_REMOTE
R3012 10K
MICOM_NON_LOGO_LIGHT
POWER_ON/OFF2_4
SOC_TX
MODEL1_OPT_3
R3013 10K
MICOM_LOGO_LIGHT
LOGO_LIGHT
MODEL1_OPT_1
RL_ON
SOC_RX
POWER_DET
R3001 10K
MICOM_M14
MHL_DET
MICOM_RESET
3D&L_DIM_EN
R3031
270K
OPT
R3021
10K
LED_R
MHL_EN
C3004
0.1uF
16V
R3028
4.7M
OPT
POWER_ON/OFF2_4
LED_R
R3007 10K
MICOM_PDP
POWER_ON/OFF2_1
LOGO_LIGHT
MICOM_DEBUG
I2C_SCL2
HDMI_CEC
MODEL1_OPT_1
+3.5V_ST
PANEL_CTL
MODEL1_OPT_3
C3000
0.1uF
POWER_ON/OFF2_2
AMP_MUTE
KEY2
IR
SCART_MUTE
D3000
BAT54_SUZHO
POWER_ON/OFF2_3
SI1012CR-T1-GE3
Q3001-*1
HDMI_CEC_FET_VISHAY
S
D
G
SW3000
JTP-1127WEM
MICOM_RESET_SW
12
4 3
MODEL1_OPT_0
MICOM_DEBUG
INV_CTL
+3.5V_ST
SOC_RESET
MODEL1_OPT_0
MICOM_RESET
R3016 1K
+3.5V_ST
GND
SIDE_HP_MUTE
R3003 10K
MICOM_H15
HDMI_CEC
+3.5V_ST
WOL_WAKE_UP
EYE_SCL
EYE_SDA
+3.5V_ST
P3000
12507WS-04L
MICOM_DEBUG
1
2
3
4
5
IC3000
R5F100GEAFB#30
1
P60/SCLA0
2
P61/SDAA0
3
P62
4
P63
5
P31/TI03/TO03/INTP4
6
P75/KR5/INTP9/SCK01/SCL01
7
P74/KR4/INTP8/SI01/SDA01
8
P73/KR3/SO01
9
P72/KR2/SO21
10
P71/KR1/SI21/SDA21
11
P70/KR0/SCK21/SCL21
12
P30/INTP3/RTC1HZ/SCK11/SCL11
13
P50/INTP1/SI11/SDA11
14
P51/INTP2/SO11
15
P17/TI02/TO02
16
P16/TI01/TO01/INTP5
17
P15/PCLBUZ1/SCK20/SCL20
18
P14/RXD2/SI20/SDA20
19
P13/TXD2/SO20
20
P12/SO00/TXD0/TOOLTXD
21
P11/SI00/RXD0/TOOLRXD/SDA00
22
P10/SCK00/SCL00
23
P146
24
P147/ANI18
25
P27/ANI7
26
P26/ANI6
27
P25/ANI5
28
P24/ANI4
29
P23/ANI3
30
P22/ANI2
31
P21/ANI1/AVREFM
32
P20/ANI0/AVREFP
33
P130
34
P01/TO00/RXD1
35
P00/TI00/TXD1
36
P140/PCLBUZ0/INTP6
37
P120/ANI19
38
P41/TI07/TO07
39
P40/TOOL0
40
RESET
41
P124/XT2/EXCLKS
42
P123/XT1
43
P137/INTP0
44
P122/X2/EXCLK
45
P121/X1
46
REGC
47
VSS
48
VDD
EDID_WP
EDID_WP
C3001
0.47uF
R3029 33
R3034
100K
R3033
27K
AR3000
3.3K
EYE_Q
HDMI2.0_CEC
R3008 22
HDMI2.0_CEC
RETENTION_DISABLE
RETENTION_DISABLE
R3009 22
HDMI1.4_CEC
WIFI_EN
X3000
32.768KHz
CRYSTAL_EPSON
X3000-*1
32.768KHz
CRYSTAL_KDS
R3010
1K
INSTANT_BOOT
INSTANT_BOOT
URSA_RESET_MICOMURSA_RESET_MICOM
POWER_DET_1
POWER_DET_1
R3000
0
C3002
15pF
C3003 18pF
MICOM
30
2012.02.22
For CEC
HDMI_WAUP:HDMI_INIT
For Debug
POWER_ON/OFF2_4
GP4 High/MID Power SEQUENCE
POWER_ON/OFF2_3
Renesas MICOM
POWER_ON/OFF!
SOC_RESET
POWER_ON/OFF2_2
Don’t remove R3014,
not making float P40
MICOM MODEL OPTION
POWER_ON/OFF2_1
OLED
MODEL_OPT_3
NON LOGO
--> MHL_EN
H15
LCD
1
For LOGO LIGHT
Need to Assign ADC port
MODEL_OPT_1
MODEL_OPT_2
0
MODEL_OPT_0
MICOM MODEL OPTION
LM15U
LOGO
HDMI2.0 CEC
* WILL EXCHANGE #12 PORT & #24 PORT FROM BO REVISION BOARD
FOR UNIFYING WITH LM14 MICOM PORT
Reserved Reserved --> 3D&L_DIM_EN
MODEL_OPT_4
Reserved Reserved
Copyright ⓒ 2014 LG Electronics. Inc. All right reserved.
Only for training and service purposes
To Next Page
Loading...
