LGB 65000 - Page 7

14
You can program the following registers:
Analog operation
Register Function Available Factory
values pre-set
CV58 Starting voltage (analog operation without wheel sensor) (1..255) [48]
To adjust the sound to the loco starting settings - if sound
starts before the loco starts moving, increase value.
CV59 max. speed (analog operation without wheel sensor) (1..255) [255]
CV64 Synchronizing the wheel sensor (see 65010 instructions) (9..255) [82]
If the wheel sensor (65010) is not installed on a drive axle,
you can adjust for different wheel diameters. You also can
program the number of magnets.
TO HERE
Digital operation with the Multi-Train System
Register Function Available Factory
values pre-set
CV1 Loco address (00..22) [3]
CV2 Starting voltage (without wheel sensor) (0..255) [0]
To adjust the sound to the loco starting settings - if sound
starts before the loco starts moving, increase value.
CV3 Acceleration (without wheel sensor) (1 = fast, 255 = slow) (1..255) [3]
CV4 Braking (without wheel sensor) (1 = fast, 255 = slow) (1..255) [3]
Hint: When programming with the 55015 Universal Remote, the following CVs are
programmed by input of the number of the desired CV in CV6 and then input of the desired
function value in CV5 (see example below).
CV5 Max. speed (without wheel sensor) (1..255) [255]
Voltage for highest speed step - if a “slower” sound at top
speed is desired, decrease value.
CV5 after input of CV6
function value for CV to be programmed
CV6 CV to be programmed
CV29 Configuration [0]
0 = normal direction
1 = reverse direction
CV55 Reset of most programmed CVs
55 = most important CVs are reset to the factory pre-set
values
CV64 Synchronizing the wheel sensor (see 65010 instructions) (9..255) [82]
If the wheel sensor (65010) is not installed on a drive
axle, you can adjust for different wheel diameters. You
also can program the number of magnets.
15
General programming procedure
with 55015 Universal Remote:
- Registers CV1 through CV4 can be
programmed directly by program-
ming the desired function value in
the register.
- To program higher CVs:
- In register CV6, input the number
of the register you want to pro-
gram.
- Then input the desired function
value in register CV5.
AUTHORIZED SERVICE
Improper service will void your war-
ranty. For quality service, contact
your authorized retailer or one of the
following LGB factory service sta-
tions:
Ernst Paul Lehmann Patentwerk
Reparatur-Abteilung
Saganer Strasse 1-5
D-90475 Nürnberg
GERMANY
Telephone: (0911) 83707 0
Fax: (0911) 83707 70
LGB of America
Repair Department
6444 Nancy Ridge Drive
San Diego, CA 92121
USA
Telephone: (858) 535-9387
Fax: (858) 535-1091
You are responsible for any shipping
costs, insurance and customs fees.
Hint: Information on LGB products
and LGB representatives around the
world is available online at
www.lgb.com
CAUTION! This product is not for
children under 8 years of age. This
product has small parts, sharp parts
and moving parts. Save the supplied
packaging and instructions.
Products, specifications and avail-
ability dates are subject to change
without notice. Some products are
not available in all markets and at all
retailers. Some products shown are
pre-production prototypes. LGB,
LGB of America, LEHMANN and the
LGB TOYTRAIN logotype are regis-
tered trademarks of Ernst Paul
Lehmann Patentwerk, Germany.
Other trademarks are the property of
their owners. © 2002 Ernst Paul
Lehmann Patentwerk.