Name: Logik L65UE18
Brand: Logik
Rating: 4 (1 reviews)

To Next Page

Thank you for purchasing your new JVC TV.

Your new TV incorporates the latest technology to enhance your viewing

experience. We would suggest that you allow about 15 mins for initial setup.

Please follow this guide for a successful rst time installation.

The latest eco-friendly power-saving technology will switch o the TV if

it is left on and idle for 4 hours. Please refer to “Auto Standby” under the

“Time Settings” section of the instruction manual for more detail.

Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.

Right Foot

Left Foot

Remote Control/

AAA Batteries x2

Feet Screws x 6

Instruction Manual

Quick Start Guide

Please inspect your TV for damage after unpacking. If

you do notice any damage please consult your dealer.

1. Open the battery compartment on the back of the remote control, you'll find a

small screw inside which can be used to secure the battery compartment cover.

2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of

the batteries with the (+) and ( - ) ends indicated in the battery compartment.

3. Click the battery compartment cover back into place. If you wish, use the small

screw to secure the battery compartment cover.

The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object, or

anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because the

screen could crack.

• Do not connect the TV to the mains supply until you have completed all the connections.

• Always disconnect the TV from the mains socket when not in use for a long period of time.

• The

button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power.

To completely disconnect the mains power, please remove the mains plug from the mains socket.

1. Connect one end of the RF coaxial cable to the aerial socket on the wall and the other end of the cable to the ANT socket on the back of your TV.

2. Plug the TV into a mains socket and switch on at the mains.

3. In standby mode, press the

button on the remote control to turn the TV on. The LED indicator will ash for a few seconds then the TV will switch on.

HDMI3

HDMI 2

(ARC)

LAN

ANT.

VGA

Optic.OUT

SPDIF

R L VIDEO

HDMI3

HDMI 2

(ARC)

LAN

ANT.

VGA

Optic.OUT

SPDIF

R L VIDEO

Router

(not included)

RF coaxial cable

(not included)

Optional

If you want to connect to the internet via a wired connection

then connect your ethernet cable to the LAN socket.

What’s in the Box?

Operating Your Remote Control

Attaching the Stand

Connecting the Aerial and Turning on the TV

Quick Start Guide

65” LED Smart 4K HDR TV

L65UE18

Setup in

15mins

Fitting the Feet to the TV

1. Ensure the TV is switched off and not connected to the mains power supply.

2. Keep the protective bag on the TV to protect it.

3. Make sure you have some help, this requires 2 people. Lay the TV down on a flat surface ideally on the edge of a table so the base of the TV slightly

overhangs the edge of the table, with the back side facing up. Please make sure a soft cushioned material (such as a dry bath towel or thick piece of foam) is

placed beneath the screen. Be very careful not to knock the edges of the TV, the screen is very fragile.

4. The feet are marked up as Left and Right. They can only be attached with the right foot on the right side of the TV as you look from the back and the left on

the left side. Attach each foot with 3 of the supplied screws.

Right FootLeft Foot

HDMI3

HDMI 2

(ARC)

LAN

ANT.

VGA

Optic.OUT

SPDIF

R L VIDEO

Table