The Logopak Cleaning Kit LogoClean Plastic is a comprehensive set designed for the maintenance and cleaning of labelling systems and their components. This kit includes various tools and cleaning agents to ensure optimal performance and longevity of Logopak equipment.

Function Description:

The primary function of this kit is to facilitate the thorough cleaning and maintenance of Logopak print engines, drive shafts, and other system components. It addresses common issues such as label residue, heavy soiling, and the need for lubrication of linear rails. The kit provides specialized cleaning solutions and tools to effectively remove contaminants and apply necessary maintenance oils, thereby preventing malfunctions and extending the lifespan of the equipment.

Important Technical Specifications:

LogoClean (Universal Cleaner):
- Contents: 1x Pump spray, 300 ml.
- Article-Nr.: 10016659.
- Use:
  - Cleaning the print head of the print engine.
  - Removing label residue on drive shafts.
  - General cleaning of labelling systems and other system components.
  - Removing all kinds of label residue from all labeller components, conveyor equipment, or the floor.
- Handling: Use according to information on the bottle. Can be used with the cleaning spatula, cleaning cloth, and cleaning sticks. Always wear enclosed gloves and observe safety data sheet directives.
LogoCare (Maintenance Oil):
- Contents: 1x Pump spray, 50 ml.
- Article-Nr.: 10016660.
- Use:
  - Filling the oiler on linear rails.
  - Directly cleaning linear rails.
- Handling: Use according to information on the bottle. Do not use for oiling piston rods of cylinders, as the oil may attack and destroy seals. Follow safety data sheet guidelines.
Cleaning Spatula:
- Description: Cleaning spatula, 100 mm.
- Contents: 3x Cleaning spatulas.
- Article-Nr.: 10016566.
- Use:
  - Cleaning the print head of the print engine.
  - Helps remove label residue or heavy soiling from the print head.
  - For large print engines, two spatulas can be used side by side.
- Handling: Moisten with LogoClean. Lift the print head, place the spatula felt-side up in the print engine, and close the print engine to clamp it. Allow the cleaning fluid to work for a few minutes. Lift the print head, remove the spatula, and clean with a cleaning stick if necessary. Cleaning can be done in the installed condition in exceptional cases, but the system must be switched off and label material removed.
Cleaning Cloth:
- Description: Cleaning cloth, white, fine felt, lint-free.
- Contents: 1 set of 5 cleaning cloths.
- Article-Nr.: 10020276.
- Use: General cleaning of labelling systems and other system components.
- Handling: Moisten with LogoClean if necessary.
Cleaning Sticks:
- Description: Cleaning sticks, plastics, w = 12 mm / ½".
- Contents: 5x Cleaning sticks.
- Article-Nr.: 10001142.
- Use: Cleaning the print head in the print engine.
- Handling: Lift the print head. Moisten the leather facing of the cleaning stick with LogoClean. Stroke the cleaning stick over the print head in the specified direction until soiling is removed. Apply a little pressure on the print head. Cleaning can be done in the installed condition, but the system must be switched off and label material removed.
Cleaning Brush:
- Description: Cleaning brush, 12 mm / ½".
- Contents: 1x cleaning brush.
- Article-Nr.: 10017114.
- Use: General cleaning of labelling systems and other system components.
Gloves:
- Description: Gloves, Nitrile, with rolled cuff; extremely tear-proof, non-powdered, and non-allergenic.
- Contents: 4x gloves.
- Article-Nr.: 10016666.
- Note: For protecting the skin from chemical splashes and cleaning agents.
Plastic Case:
- Description: Plastic case.
- Contents: 1x plastic case.
- Article-Nr.: 10016664.
- Use: For storing the entire cleaning kit.

Usage Features:

The kit is designed for ease of use and versatility, allowing for both routine maintenance and more intensive cleaning tasks. The various tools and solutions are tailored to specific components, ensuring effective and safe cleaning. The inclusion of gloves and safety data sheets emphasizes user safety during handling of chemical agents. The ability to perform some cleaning tasks in an installed condition (with proper precautions) minimizes downtime.

Maintenance Features:

The kit itself is a maintenance tool. Its components are designed to maintain the operational efficiency of Logopak labelling systems. The plastic case provides a convenient and organized storage solution for all items, ensuring they are readily available when needed and protected from damage or loss. Regular use of the kit's contents, as per the instructions, contributes significantly to the preventive maintenance strategy for Logopak equipment, reducing the likelihood of breakdowns and costly repairs.

LOGOPAK LogoClean Plastic - Protective Gloves

Table of Contents