To Next PageTo Next Page
Need help?Do you have a question about the Lopi Yankee and is the answer not in the manual?
General| Brand | Lopi |
|---|---|
| Model | Yankee |
| Category | Pellet stove |
| Language | English |
Details important information about serial numbers and warranty registration.
Details the heating capacity, burn rate, and hopper capacity of the stove.
Provides the physical measurements of the stove, including weight.
Lists the electrical ratings, start-up, and operation wattages.
Specifies the type of fuel the unit is designed for and its required standards.
States the EPA certification status and testing laboratory.
Crucial safety warnings and initial checks before starting installation.
Lists all components included with the pellet stove kit.
Outlines the different ways the stove can be installed (e.g., residential, alcove).
Guidance on planning the installation, including sketching and curing the paint.
Requirements for safely placing the stove, including clearance distances.
Details the necessary non-combustible floor protector specifications.
Diagrams and measurements for clearances in straight vent installations.
Diagrams and measurements for clearances in corner vent installations.
General guidelines and warnings for installing the pellet stove venting system.
Graphical representation of maximum allowable venting distance and height.
Specifies the required type and diameter of pellet vent for installation.
Instructions on sealing vent sections and achieving proper horizontal alignment.
Details requirements for the vent cap, house shield, and termination location.
Specific installation rules and warnings for mobile homes, including safety warnings.
Guidance on connecting an outside air source for proper combustion.
Specific clearance and dimension requirements for alcove installations.
Instructions for adjusting intake and exhaust restrictors for optimal performance.
Diagram illustrating a direct through-the-wall vent installation with clearances.
Diagram showing an interior vertical vent installation with clearances and components.
Diagram for retrofitting a Class A chimney with the pellet stove.
Diagram showing installation into a masonry fireplace with vent connections.
Diagram for installing into a zero-clearance metal fireplace.
Diagram illustrating installation into an interior masonry chimney.
Identifies the location of the control panel, firepot, and door handle.
Guides on initial startup, including paint curing and auger priming.
Instructions on how to properly fill the pellet hopper.
Explains the Manual and Auto modes for controlling the heater's operation.
Detailed steps for starting, shutting down, and adjusting heat in Manual mode.
How to use the FAN dial to control the convection blower speed.
Guides on using Auto mode with a thermostat for temperature control.
How to adjust the 'Heat Output' dial for desired heating levels in Auto mode.
Explains the sequence the stove follows when starting or changing modes.
Indicates the function of the 'AUGER ON' light.
Describes when the 'FAULT' light illuminates and how to reset it.
Details how the stove behaves during and after a power outage.
Routine checks and tasks to perform daily when using the stove.
How to check the flame condition for proper burning.
Troubleshooting steps when pellets accumulate in the firepot.
Identifying and troubleshooting clinkers in the firepot.
Step-by-step instructions for cleaning the firepot.
Tasks to perform every 10 bags of pellets or bi-weekly.
Procedure for cleaning the heat exchange tubes.
Instructions for cleaning the pellet hopper.
Guidance on cleaning optional gold surfaces on the door and grill.
Instructions on how to open the stove door for maintenance.
Detailed steps for cleaning ash from the firebox into the ashpan.
Procedure for checking and disposing of ashes from the ashpan.
How to clean the stove's viewing glass for better visibility.
Extensive maintenance procedures recommended annually or every two tons of fuel.
Instructions for cleaning the vertical exhaust duct system.
Steps for accessing and cleaning the main exhaust duct.
Procedure for cleaning the exhaust blower motor and housing.
Guidance on inspecting and cleaning the pellet vent system for build-up.
How to inspect and seal air leaks around the door, glass, and ashpan.
Step-by-step guide for installing the optional thermostat.
Information on using the remote thermostat and its operating characteristics.
Instructions for assembling and installing the pellet log accessory.
