This document is a user manual for Upper Bounce Enclosure Sets and Enclosure Nets, designed to fit most trampoline models. It provides comprehensive instructions for assembly, installation, care, maintenance, and use of these trampoline accessories.
Function Description:
The Upper Bounce Enclosure Set and Enclosure Net serve as safety barriers for trampolines, preventing users from falling off the jumping surface. The enclosure net creates a protective wall around the trampoline, ensuring a safer jumping experience. Different models are available to accommodate various trampoline types and sizes, including "Inside type" enclosure sets, "Outside type" enclosure sets, "Enclosure Nets Only," and "FLEX ON TOP enclosure sets."
Important Technical Specifications:
The manual categorizes models based on their type and size, providing specific part lists and installation instructions for each.
Measuring Tips for Enclosure Set:
To ensure the correct enclosure set is purchased, users must measure their trampoline's frame size and count the number of poles.
- Frame Size: Measure the trampoline frame from one outside edge vertically and horizontally to the other outside edge.
- Pole Amount: Count the number of legs on the trampoline. The manual provides diagrams for connecting 2 poles to each leg.
- Pole Connector: Measure the diameter of the trampoline leg. A 1.75" connector is required if the leg measures up to 1.75".
Measuring Tips for Enclosure Net:
For enclosure nets, users need to verify the frame size, the number of poles/arches, and the height of the product.
- Height Chart of All Types of Nets:
- 7.5 ft: 65"
- 8 ft: 65"
- 9 ft: 65"
- 10 ft: 64"
- 12 ft and +: 71"
Enclosure Set Parts List (Example for UBES104, UBES124, UBES144, UBESOS124, UBESFG144, UBES86, UBES126, UBES146, UBES156, UBES106, UBES136, UBES166, UBESOS7.56, UBESOS126, UBESOS136, UBESOS146, UBESOS156, UBESFG86, UBESFG116, UBESFG126, UBESFG136, UBESFG146, UBESFG156, UBES128, UBES148, UBES158, UBES138, UBESOS138, UBESOS148, UBESOS158, UBESFG158, UBESFG155, UBESFG178):
- Upper Pole (A): Available in "For FG Type" (0, 4, 0, 6, 0, 8, 5 units depending on model) and "For ES/OS Type" (4, 0, 6, 0, 8, 0, 0 units).
- Lower Pole (B): 4, 6, 8, 5 units.
- Clamp Tool Set (C): 8, 12, 16, 16 units.
- Tool (D): 1 unit.
- Pole Cap (E):
- "For Inside Type" (E-1): 4, 0, 6, 0, 8, 0, 0 units.
- "For Outside Type" (E-2): 4, 0, 6, 0, 8, 0, 0 units.
- "For FG Type" (E-3): 0, 4, 0, 6, 0, 8, 5 units.
- Enclosure Net (F): 1 unit.
- Big Rope (G): 1 unit.
- PVC Sleeve (T): 4, 6, 8, 5 units (not used if an outside net is present).
Usage Features:
Pole Installation Instructions:
- Required: 2 adults in good physical condition, proper shoes, and balance are necessary for assembly.
- Parts Placement: Lay out all parts before starting.
- Pole Types:
- Straight poles: Use tapered lower poles.
- Curved poles: Use curved poles as upper poles.
- Clamping:
- Clasp the lower enclosure pole into the rounded end of the clamp, ensuring the black rubber cap faces down.
- If the pole fits loosely, insert the green rounded piece before clasping.
- If the pole is too thick, remove the green rounded piece.
- Insert the plastic bracket until it reaches the pole.
- Clamp Placement: Two clamps per pole; one 2" below the frame, the other 2" above the end of the lower pole.
- Securing: Insert the plastic bracket, clasp the trampoline leg into the clamp, and secure tightly with steel brackets and nuts.
- Upper Pole Insertion: Insert the upper pole into the lower pole.
- PVC Sleeve: Cover all poles with the PVC Sleeve (Item T).
- Pole Caps:
- Inside type net: Use part E1.
- Outside type net: Use part E2.
- Curved poles: Use provided pole caps.
Net Installation Instructions (Inside Type Models):
- Logo Placement: Ensure the Upper Bounce logo is on the outside of the trampoline.
- Securing the Top of the Net:
- Straight Pole Enclosure Set: If a "C" Type pole cap is present, hook all straps into "C" and follow step 2. If a plain pole cap is present, wrap all straps around the cap and follow step 2.
- Trampoline with Arches: Connect straps to arches and tighten.
- Ring on Top Enclosure Set: Refer to page 12 for instructions.
- Securing the Bottom of the Net:
- Connect the net to the V-rings of the trampoline mat using attached clips at regular intervals.
- Secure one end of the rope by knotting it to the V-ring closest to one side of the entrance zipper.
- Weave the rope through the net and every second V-ring, moving around the trampoline away from the entrance zipper.
- Secure the other end of the rope by knotting it to the V-ring closest to the other side of the entrance zipper.
Net Installation Instructions (Outside Type Models):
- Securing the Top of the Net:
- Install the net to the poles by inserting the beginning of the sleeve onto the poles until it reaches 2 ft. Repeat for all poles.
- Pull down each sleeve a few inches at a time until all sleeves reach the bottom of the enclosure frame.
- Securing the Bottom of the Net:
- Option A (Outside of trampoline): Connect bottom straps/clips to every few jumping mat V-rings from under the Safety Pad. Attach clips from the outside.
- Option B (Inside of trampoline): Pull the net closer to the mat on the bottom and connect bottom straps/clips to every few jumping mat V-rings. The bottom of the net should be between the pad and the mat.
Net Installation Instructions (Arch Type Models):
- Securing the Top of the Net:
- Disconnect the top arches and slide the top arch part into the sleeve.
- Click the arch part and poles together tightly.
- Securing the Bottom of the Net: Refer to page 9 for rope installation instructions.
Net Installation Instructions (FLEX ON TOP Models):
- Step 1: Connect the Pole Caps to the top of the poles with screws.
- Step 2: Run the fiberglass into the top sleeves of the net, connecting one fiber to another while running it from one sleeve to the next. Start by clicking the fiberglass rods together until all rods are finished.
- Step 3: Run the Fiberglass Rods through the sleeves opening at the upper edge of the safety net until the other side of the sleeve is reached.
- Step 4: After inserting top rods through all sleeves, connect all rods together using one of several methods:
- With T pole caps.
- With nuts that connect it together with an Adjustable Wrench.
- Connect each other by just clicking them together.
- At the last point, add the connector to complete the circle.
- Step 5: To connect the ring, have another person stand on the opposite side and push the rods towards the center.
- Step 6: Insert the assembled rod circle into the opening of the pole cap.
- Step 7: Refer to page 9 for rope installation instructions.
Maintenance Features:
The manual includes a "Replacement Parts List" for various trampoline components, ensuring long-term usability and maintenance.
- Jumping Mats: Listed by size (e.g., UBMA T-7.5-42-5.5 for 7.5 ft, UBMA T-8-40-5.5 for 8 ft, UBMA T-10-56-5.5 for 10 ft, etc.).
- Safety Pads: Listed by size and color (e.g., UBPAD-S-7.5-B for 7.5 ft Blue, UBPAD-S-8-B/G for 8 ft Blue/Green, etc.).
- Safety Nets:
- Strap Type Net (Inside): UBNET-7.5-6-IS, UBNET-8-6-IS, UBNET-10-4-IS, UBNET-10-6-IS, UBNET-10-8-IS, UBNET-11-6-IS, UBNET-12-4-IS, UBNET-12-6-IS, UBNET-13-6-IS, UBNET-14-4-IS, UBNET-14-6-IS, UBNET-14-8-IS, UBNET-15-6-IS, UBNET-15-8-IS, UBNET-16-6-IS.
- Strap Type Net (Outside): UBNET-7.5-6-OS, UBNET-8-6-OS, UBNET-10-8-OS, UBNET-12-4-OS, UBNET-12-6-OS, UBNET-13-6-OS, UBNET-14-6-OS, UBNET-14-8-OS, UBNET-15-6-OS, UBNET-15-8-OS.
- Sleeves on Top - Net (Arch): UBNET-6-3-AST, UBNET-7-3-AST, UBNET-8-2-AST, UBNET-11-3-AST, UBNET-12-4-AST, UBNET-12-2-AST, UBNET-13-2-ASTR, UBNET-13-4-AST, UBNET-14-4-AST.
- For Curved Poles: UBNET-8FG-4, UBNET-11FG-6, UBNET-12FG-4, UBNET-13FG-6, UBNET-14FG-6, UBNET-17FG-8.
- Weather Covers: Black (UBWC-7.5-BK, UBWC-8-BK, UBWC-10-BK, UBWC-12-BK, UBWC-13-BK, UBWC-14-BK, UBWC-15-BK, UBWC-16-BK) and Blue (UBWC-7.5-BL, UBWC-8-BL, UBWC-12-BL, UBWC-14-BL, UBWC-15-BL).
- Other Type Parts:
- Square Mats (UBMA TSQ-13)
- Oval Mats (UBMA TO-1614-96-7, UBMA TO-1715-96-7)
- Band Mats (UBMA B-11376, UBMA B-1484)
- Safety Pads Square (UBPADSQ-13)
- Safety Pads Rectangular (UBPADRTG-S-148-B, UBPADRTG-S-159-B)
- Safety Pads Oval (UBPADO-1715, UBPADO-1614)
- Arch Net - Square (UBNETSQ-1313-4)
- Oval Net (UBNETO-1614, UBNETO-1715)
- Universal Net Type (UBNET-U1, UBNET-U2)
Other Accessories:
- Ladder (UBL3S-42-G)
- Ladder with Flat Steps (UBLBFS3-42)
- Trampoline Shoe Bag (UBSHB-3)
- Trampoline Anchor Kit (Set of 4) (UBHWD-AK-4)
- Deep Fastening Spiraled Anchor Kit - Set Of 4 (UBHWD-AKB-4)
- Trampoline Spring Pull Tool (T-Hook) (UBHWD-TH)
- Upper bounce® Trampoline Jumping Skate (UB-TJB)
The manual emphasizes the availability of a wide variety of replacement parts compatible with most trampolines, regardless of their brand. Customer service is available via phone (1-845-810-0083) or email (support@machrus.com) for assistance with finding replacement parts.
Need help?
General
To Next Page