, TYPICAL WAYSTO CONNECT OUTSIDE
TO WATERSUPPLY Wash regularlywith mild soap and water.
rinse with clear water. Never use abrasive
scouring powders, automobile polish or fur-
niture polish.Appliance Wax or a similarpro-
duct will clean and protect the finish satis-
factorily.
Your door gaskets are vinyl. They may
be cleaned with a baking soda solution,
_1_ I soap and water or with a mild scouring
powder.
,= Through The FlCOtTOBasementColdWater Pipe
_ DEFROST PAN
6. Locate the brass nut and sleeve , IJ Defrost water drains into a shallow pan
which comes with the saddle valve. _/ beneath the cabinet and evaporates. Dur-
Slide them onto the ¼" copper tub- ing periods of high humidity, water could
ing. Insert the end of the tubing into remain in the pan. This pan should be
the saddle valve as far as it will go cleaned once a month with a solution of
and tighten the nut with an adjusts- strong soap and water.
ble wrench. Turnoff the saddle valve.
7. Turn ON the main water supply and . f//_J_--,
flush out the pipe until the water runs
clear. At the same time, check for ,.t,_C,.w,S_.Und_,You,.om_
leaks at the saddle valve. Next pre-
pare to flush out the ¼" tubing. Po-
sition a bucket or other container at To remove the defrost pan, grasp the base
the open end of the ¼'" tubing so it _'_ grille at both ends and pull it straight out.
will catch the water. Turn on the sad- _ Slide the pan out from underneath the
die valve and allow water to flow un- I___1 cabinet.
til it has cleared. Turn off saddle valve. ,.i S_FORT_A,LS
8. Connect the water line from the sad- _ ILl /_EF_o_rm.
die valve to the water valve as shown .... _L 1 __
Insert the water line into the com- UctderTheSinkToTheColdWater_pe
pression union as far as it will go.
Tighten each brass nut with one
wrench on the nut and the other _ To replace the defrost pan, position the
wrench on the compression union. _ side flanges to fit over slide railsand push it
Return water line to vertical. Secure in until it stops.
water supply line clamp. Tighten hose _ To replace base grille, align spring clips
nut with pliers, with square opening in cabinetand tap each
and until grille locks in place.
r Thewaterintet tubing assemblyrequired
to complete the water connectionto the CONDENSER
watervalveislocatedinthe crisperdrawer in = Your refrigerator will operate more er-
a bag, ThrOugh The WalPTo The Utility Room ColdWater Flpe
ficiently when the condenser is clean. It
C'>) CAUTION: ic e Melter tubing _ld itot bo inltlllled should be cleaned at least twice a year or
T,_tenReturnwale, su_p=vh_etove.,Ca=ho_enut onwe=weSecure Wae_ou_nupp_mv where temper=ture may fell below frmwJ.g, more often if conditions require it. It can
w_ter linewith clamp "_
_ I ,,_ be adequately cleaned through the right
front of the base opening. Grasp the base
grille at both ends and pull straight out.
_=_'_1 \/ :l I ,_S ............ ELF_PLACING Then reach through the base opening with
HOSe Nut _/_ I ] , I _' _ ....... line your vacuum cleaner attachment to clean
.......... LIGHT BU LB thefrontandopenendofthecondenser.water Supply I r _ wate[lines
\ _ ))_V/t_jr_xf_ _ i_['??........ °C'°° DISCONNECT THE POWER .-_1
.......... CO.DBE,=O.E.EPLAC,NG
................ LIGHT BULBS
Lmeassh_n
ALWAYS USE A 40 WA'l-r, STANDARD
9 .Turn on saddle valve. Tighten any BASE, APPLIANCE TYPE BULB WHEN RE-
connections that leak. PLACING A LIGHT.
To replace base grille, align spring clips
10. Re-install the fiber panel and secure CLEANING with square opening in cabinet and tap each
with the screws removed and saved end until grille locks in place.
in Step 1. DISCONNECT THE POWER
11. Plug in the power cord and push the CORD BEFORE CLEANING GOING ON
refrigerator into place, arranging the INSIDE
copper tubing so that is does not vi-
brate against the back of the refriger- Clean both compartments and inner door VACATION
panelswith mild soapand water. Do not use
ator or against the wall. an abrasive powder, solvent, polish cleaner If you will be gone for a month or less,
or undiluted detergent, leave the control knob at its usualsetting.
IMPORTAN3_ Because the refrigerator You may notice a slight discolorationap- During longer absences, (a) remove all
and icemaker are warm, it may take up peering at the top and nearthe center of the food, (b) disconnectfrom electricaloutlet, (c)
to 12 hours before the icemaker back wall of the fresh food compartment, clean the refrigerator thoroughly, including
produces the first supply of ice cubes. This is no cause for alarm, but it should be defrost pan, (d) leave doors open to prevent
cleaned off periodically, odor formation.
To Next Page
Loading...
Need help?
General
