Magnum Energy ME-AGS-N User Manual

Owners Manual
Version 5.0
ME-AGS-N
Automatic Generator Start
for Network Versions
For use with the following remote controls:
ME-RC Revisions 1.5  2.612
ME-ARC Revisions 2.0  2.4
ME-RTR Revisions 2.1  2.2

Magnum Energy ME-AGS-N Specifications

General

Model	ME-AGS-N
Type	Automatic Generator Start Controller
Compatibility	Magnum Energy inverters
Remote Start Capability	Yes
Input Voltage	12 VDC
Generator Start Methods	Manual
Start Signal Output	Dry Contact Relay
Generator Run Time	Adjustable
Cool Down Time	Adjustable
Battery Voltage Start Setpoints	Adjustable
Battery Voltage Stop Setpoints	Adjustable
Status Indicators	LED indicators

Summary

Important Safety Instructions

2.0 Installation

2.1 Installation Requirements

Outlines prerequisites and considerations before installing the AGS module.

2.3 Mounting Procedure

Step-by-step instructions for physically mounting the AGS module.

2.4 Connecting the Cables

Instructions for connecting the temp sensor and network communication cables.

2.4.1 Connecting the Remote Temp Sensor Cable

Details on connecting the remote temperature sensor cable.

2.4.2 Connecting the Network Communication Cable

Instructions for connecting the network communication cable.

2.4.3 Cable Connections with Multiple Devices

Explains how to connect multiple networked devices using Star or Daisy Chain configurations.

2.5 ME-AGS-N Terminal Block Wiring Connections

Detailed guide for wiring the AGS module's terminal block to the generator.

2.5.1 Power Connections (Terminals 3 & 4)

Instructions for connecting power to the AGS module using terminals 3 and 4.

2.5.2 Generator Run Sense Connection (Terminals 2 & 4)

How to connect the generator run sense signal to the AGS module.

2.5.3 Gen Start/Stop Connections (Terminals 1, 5, 6, 7, & 8)

Wiring instructions for generator start/stop control relays.

3.0 ME-AGS-N Module Setup

3.1 Configuring the Internal ME-AGS-N Settings

Steps to configure the input DC voltage jumper and DIP switch for Gen Type.

4.0 ME-AGS-N Module Functional Tests

4.1 Power-Up Test

Test to verify correct polarity and power application to the AGS module.

4.2 Generator Wiring Test

Test to confirm generator start/stop wiring and Gen Type configuration.

5.0 ME-AGS-N Module Operation

5.1 ME-AGS-N Module TEST Pushbutton

Explains the function and use of the TEST pushbutton for system testing.

6.0 ME-AGS-N Module Troubleshooting

6.1 Using the ME-AGS-Ns LED Indicators

How to interpret LED indicators for troubleshooting AGS operational problems.

6.2 Generator Starting/Running Troubleshooting

Troubleshooting steps for generator start or run issues based on AGS status.

8.0 Using the ME-RC Remote

8.1 ME-AGS-N Setup using the ME-RC

Steps to set up autostart and autostop conditions using the ME-RC remote.

8.2 ME-AGS-N Functional Testing using the ME-RC

How to perform functional tests of the AGS system via the ME-RC remote.

8.4 Enabling the ME-AGS-N using the ME-RC

8.5 Starting and Stopping the Generator using the ME-RC

9.0 Using the ME-ARC Remote

9.1 ME-AGS-N Setup using the ME-ARC

9.2 ME-AGS-N Functional Tests using the ME-ARC

9.2.1 Remote to Generator Communication Test

9.4 Enabling the ME-AGS-N using the ME-ARC

9.5 Starting and Stopping the Generator using the ME-ARC

10.0 Using the ME-RTR Router

10.1 ME-AGS-N Setup using the ME-RTR

10.2 ME-AGS-N Functional Tests using the ME-RTR

10.2.1 Router to Generator Communication Test

10.4 Enabling the ME-AGS-N using the ME-RTR

10.5 Starting and Stopping the Generator using the ME-RTR

12.0 ME-AGS-N Remote Troubleshooting

12.1 AGS Fault Message Screens for Magnum Remotes

12.2 Resolving Operational Statuses

12.3 ME-AGS-N Faults using your Remote

Detailed remedies for specific AGS fault conditions like Fault Temp, Fault Test, etc.

12.3.1 How to Clear AGS Faults

Procedure to clear AGS faults and re-enable the system for autostart.