EasyManua.ls Logo

Majestic Napoli User Manual

Majestic Napoli
15 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Napoli Installation Guide - Surface Profiles
1
The Majestic Shower Company Limited
17 Flitch Industrial Estate, Chelmsford Road, Dunmow, CM6 1XJ
Telephone +44 (0) 8448 001 500
Facsimile +44 (0) 1279 635 074 info@majesticshowers.com www.majesticshowers.com
Thank you for purchasing this Napoli shower screen. Please study these instructions
carefully before assembly and installation.
Checking of Parts
Parts are listed at the beginning of this guide. Please check all supplied parts immediately
and contact the Majestic Shower Company in the event of any missing or damaged parts.
These instructions are for left and right-handed units. All parts are reversible.
Handling of Parts
When handling glass, use suction glass lifters and take care to ensure that corners or edges
are not knocked. Do not place glass on hard surfaces - place cushioning material under-
neath to prevent the glass from shattering.
Unwrap all metal parts carefully to prevent damaging the plated surfaces.
Pre Installation Checks
Prior to undertaking installation, check the accuracy of the following against specifications
for the particular installation location:
-
Verticality and flatness of walls. Where wall profiles are used, some lean in or lean out of
the wall relative to the floor or tray can be accommodated (+/- 9mm if 24mm profile is used,
+/- 5mm if 17mm profile is used). Walls must be substantially flat.
-
Levelness and flatness of the floor or tray. Where a profile or underframe is used under-
neath a glass panel, any minor hollows in the mounting surface must be solidly packed to
prevent deflection under the weight of the glass as this may over stress the glass.
Installation Tips
The general principle of assembly is to assemble parts in the steps shown - first a dry
assembly to check fits or mark cutting or drilling positions and then a final assembly with
silicone.
When cutting aluminium extrusion, wrap the profile with masking tape first and cut through
the taped area - this will help protect the surrounding surface. Use a fine file to smooth cut
edges.
If anti-calcium glass has been specified, the treated side of the glass will be indicated and
should always face inwards towards the wet side of the shower area.
DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS
Question and Answer IconNeed help?

Do you have a question about the Majestic Napoli and is the answer not in the manual?

Majestic Napoli Specifications

General IconGeneral
Product TypeBathtub
TypeFreestanding
MaterialAcrylic
ShapeOval
ColorWhite

Summary

Underframe Installation

Step 1: Measure and Position Underframe

Measure alcove, check tolerances, and position underframe 10mm from tray edge or mark floor.

Step 2: Apply Silicone and Secure Underframe

Apply silicone to underframe underside and corners, then tape in place while silicone sets.

Vertical Profile and Wall Bracket Fixing

Step 3: Align Vertical Profiles

Use spacer to align vertical profiles, check plumbness, mark holes, and remove profiles.

In Line Panel Placement

Glass to Wall Bracket Attachment

Securing Vertical Profiles and Brackets

Finalizing In Line Panel and Brackets

Door Hinge Attachment

Step 13: Hinge Preparation and Assembly

Insert rubber strips in hinge slots, assemble hinges and face plates with gaskets, and loosely screw together.

Step 14: Align and Tighten Hinges

Position hinges centrally, align with glass edge, ensure 90-degree angle, and tighten screws to torque.

Door Mounting and Hinge Finalization

Step 15: Position Door onto Blocks

Insert rubber strips in door hinge slots, position door mounting blocks, and lift door onto blocks.

Step 16: Final Hinge Adjustment and Tightening

Align hinges, loosely screw, adjust alignment, tighten hinges to torque, and remove mounting blocks.

Final Sealing and Hinge Bias

Step 24: Adjust Hinge Bias

Adjust hinge bias using grub screws to pull the door into the seal for proper alignment.