10 ENGLISH
FUNCTIONAL
DESCRIPTION
CAUTION: Before adjusting or checking func-
tion on the tool, always release the trigger and
disconnect the air hose from the tool.
Adjusting depth of nailing
CAUTION: Always release the trigger and
disconnect the hose before adjusting the depth
of nailing.
Fig.5 : 1. A d j uster
T o ad j ust th e d epth of nailing, turn th e ad j uster.
T h e d epth of nailing is th e d eepest w h en th e ad j uster
is turned fully in the A direction shown in the gure. It
w ill bec ome sh allow er as th e ad j uster is turned in th e B
d irec tion.
I f nails c annot be d riv en d eep enough ev en w h en th e
ad j uster is turned f ully in th e A d irec tion, inc rease th e
air pressure.
I f nails are d riv en too d eep ev en w h en th e ad j uster is
turned f ully in th e B d irec tion, d ec rease th e air pressure.
G enerally speaking, th e tool serv ic e lif e w ill be longer
w h en th e tool is used w ith low er air pressure and th e
ad j uster set to d eeper d epth of nail d riv ing.
Hook
CAUTION: Always release the trigger and
disconnect the hose before changing the hook
position.
CAUTION: Never hook the tool at high loca-
tion or on potentially unstable surface.
CAUTION: Do not hang the hook from the
waist belt. I f th e nailer ac c id entally d rops, it may
result in misring and personal injuries.
Fig.6
Fig.7: 1. H ook 2. H ex soc ket bolt 3. H ole
T h e h ook is c onv enient f or h anging th e tool temporarily .
T o c h ange th e h ook position, remov e th e h ex soc ket
bolt and sw itc h th e h ook d irec tion. T h e h ook h as tw o
h oles. C h oose th e h ole d epend ing on y our pref erable
h ook w id th .
ASSEMBLY
CAUTION: Before carrying out any work on
the tool, always release the trigger and discon-
nect the air hose from the tool.
CAUTION: Load the same type, size and
uniform length of nails when loading nails in the
magazine.
Loading nailer
1. S lid e th e push er lev er until it is loc ked at th e mag-
az ine end .
Fig.8: 1. P ush er lev er
2. I nsert a strip of nails into th e slit in th e rear of th e
magazine and push the strip toward the ring opening.
Fig.9: 1. S trip of nails 2. Magaz ine
3. P ress th e loc k lev er w h ile slid ing th e push er lev er
tow ard th e magaz ine end .
Fig.10: 1. P ush er lev er 2. L oc k lev er
4. R eturn th e push er lev er.
CAUTION: Do not put your nger on the rail
of the pusher lever. D oing so may c ause personal
injury by the pusher lever swiftly returns to the ring
opening.
Fig.11
Correct loading of the nails
CAUTION: Be sure to load nails in the correct
direction.
Be sure to load th e nail at th e c orrec t angle. Nails w ill be
parallel w ith th e d riv er guid e if c orrec tly set.
Fig.12
W h en load ing tw o or more strips of th e nails, set th e
nail h ead of th e latter strip properly ov erlaps th at of th e
f ormer strip.
Fig.13
A lw ay s set th e loc k of th e push er lev er to h old th e nail
h ead as illustrated .
Fig.14: 1. L oc k of th e push er lev er
Connecting air hose
CAUTION: Do not rest your nger on the
trigger when connecting the air hose.
Fig.15 : 1. Air tting 2. A ir soc ket
Slip the air socket of the air hose onto the air tting on
the tool. Be sure that the air socket locks rmly into
position when installed onto the air tting.
A h ose c oupling must be installed on or near th e tool in
suc h a w ay th at th e pressure reserv oir w ill d isc h arge at
th e time th e air supply c oupling is d isc onnec ted .
OPERATION
CAUTION: Make sure all safety systems are in
working order before operation.
To Next Page
Loading...
