Makita DTM50 - Specifications

2 ENGLISH
SPECIFICATIONS
Model DTM40 DTM50
Oscillation per minute 6,000 - 20,000 (min
-1
)
Oscillation angle, left/right 1.6 ° (3.2 ° total)
Overall length 307 - 324 mm
Net weight 1.7 - 2.0 kg 1.8 - 2.2 kg
Rated voltage D.C. 14.4 V D.C. 18 V
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydifferfromcountrytocountry.
• Theweightmaydifferdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Batterycartridge D.C.14.4 V Model BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
D.C.18 V Model BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges
andchargersmaycauseinjuryand/orre.
Symbols
Thefollowingshowthesymbolsusedfortheequip-
ment.Besurethatyouunderstandtheirmeaningbefore
use.
Read instruction manual.
Wearsafetyglasses.
Ni-MH
Li-ion
OnlyforEUcountries
Donotdisposeofelectricequipmentor
batterypacktogetherwithhouseholdwaste
material!
In observance of the European Directives,
on Waste Electric and Electronic
EquipmentandBatteriesandAccumulators
and Waste Batteries and Accumulators
and their implementation in accordance
withnationallaws,electricequipmentand
batteriesandbatterypack(s)thathave
reached the end of their life must be col-
lectedseparatelyandreturnedtoanenvi-
ronmentallycompatiblerecyclingfacility.
Intended use
The tool is intended for sawing and cutting wood,
plastic,gypsum,non-ferrousmetals,andfastening
elements (e. g. unhardened nails and staples). It is also
intendedforworkingsoftwalltiles,aswellasdrysand-
ingandscrapingofsmallsurfaces.Itisespeciallyfor
workingclosetoedgeandushcutting.
Noise
ThetypicalA-weightednoiseleveldeterminedaccord-
ing to EN62841:
Work mode: Sanding
Sound pressure level (L
pA
) : 78 dB (A)
Uncertainty(K):3dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
Work mode: Cutting with plunge cut saw blade
Model DTM40
Sound pressure level (L
pA
) : 82 dB (A)
Sound power level (L
WA
) : 93 dB (A)
Uncertainty(K):3dB(A)
Model DTM50
Sound pressure level (L
pA
) : 84 dB (A)
Sound power level (L
WA
) : 95 dB (A)
Uncertainty(K):3dB(A)
Work mode: Cutting with segmental saw blade
Sound pressure level (L
pA
) : 81 dB (A)
Sound power level (L
WA
) : 92 dB (A)
Uncertainty(K):3dB(A)
Work mode: Scraping
Model DTM40
Sound pressure level (L
pA
) : 81 dB (A)
Sound power level (L
WA
) : 92 dB (A)
Uncertainty(K):3dB(A)
Model DTM50
Sound pressure level (L
pA
) : 83 dB (A)
Sound power level (L
WA
) : 94 dB (A)
Uncertainty(K):3dB(A)