Manitou MC 50 POWERSHIFT 3-E2 Series - Page 134

3 - 31
C4 - FRONT AXLE DIFFERENTIAL OIL LEVEL
CHECK
MC 30 Série 3-E2 M26-2 Série 3-E2 M26-4 Série 3-E2 M40-4 Série 3-E2
M30-2 Série 3-E2 M30-4 Série 3-E2 M50-4 Série 3-E2
MC 40/50 POWERSHIFT Série 3-E2 (up to machine no 218949)
MC 60/70 POWERSHIFT Série 3-E2
Place the lift truck on level ground with the I.C. engine stopped.
- Remove level plug 1 (fig. C4). The oil should be flush with the edge of the hole.
- If necessary, add oil (see: 3 - MAINTENANCE: LUBRICANTS AND FUEL) by the filler port 2
(fig. C4).
- Replace and tighten the level plug 1 (fig. C4) (tightening torque 34 to 49 N.m).
C4 - FRONT AXLE DIFFERENTIAL OIL LEVEL
CHECK
MC 40/50 POWERSHIFT Série 3-E2 (from machine no 218950)
Place the lift truck on level ground with the I.C. engine stopped.
- Remove level plug 1 (fig. C4). The oil should be flush with the edge of the hole.
- If necessary, add oil (see: 3 - MAINTENANCE: LUBRICANTS AND FUEL) by the same hole.
- Replace and tighten the level plug 1 (fig. C4) (tightening torque 34 to 49 N.m).
C5 - FRONT WHEELS REDUCERS OIL LEVEL
CHECK
Place the lift truck on level ground with the I.C. engine stopped.
- Check the level on each front wheel reducer.
- Place level plug 1 (fig. C5) in the horizontal position.
- Remove the level plug ; the oil should be flush with the edge of the hole.
- If necessary, add oil (see: 3 - MAINTENANCE: LUBRICANTS AND FUEL) by the same hole.
- Replace and tighten the level plug 1 (fig. C5) (tightening torque 34 to 49 N.m).
C6 - REAR AXLE DIFFERENTIAL OIL LEVEL
CHECK
M26-4 Série 3-E2 M40-4 Série 3-E2
M30-4 Série 3-E2 M50-4 Série 3-E2
Place the lift truck on level ground with the I.C. engine stopped.
- Remove level plug 1 (fig. C6). The oil should be flush with the edge of the hole.
- If necessary, add oil (see: 3 - MAINTENANCE: LUBRICANTS AND FUEL) by the filler port 2
(fig. C6).
- Replace and tighten the level plug 1 (fig. C6) (tightening torque 34 to 49 N.m).
C7 - REAR WHEELS REDUCERS OIL LEVEL
CHECK
M26-4 Série 3-E2 M40-4 Série 3-E2
M30-4 Série 3-E2 M50-4 Série 3-E2
Place the lift truck on level ground with the I.C. engine stopped.
- Check the level on each rear wheel reducer.
- Place level plug 1 (fig. C7) in the horizontal position.
- Remove the level plug ; the oil should be flush with the edge of the hole.
- If necessary, add oil (see: 3 - MAINTENANCE: LUBRICANTS AND FUEL) by the same hole.
- Replace and tighten the level plug 1 (fig. C7) (tightening torque 34 to 49 N.m).
C4
C5
2
1
C4
1
1
C6
C7
2
1
1