1-141-14
500 mm500 mm
B2B2
11
22
33
CC
-- For irregular loads, determine the trFor irregular loads, determine the transverse centre of gravity ansverse centre of gravity before any movement (before any movement (fig.fig.
B2) and set it in the longitudinal axis of the lift trB2) and set it in the longitudinal axis of the lift truck.uck.
It is forbidden to move a It is forbidden to move a load heavier than the effective capacity defined on the load heavier than the effective capacity defined on the lift truck load chart.lift truck load chart.
For loads with a moving centre of gravity (e.g. liquids), take account of the variations in the centre ofFor loads with a moving centre of gravity (e.g. liquids), take account of the variations in the centre of
gravity in order to gravity in order to determine the load to be handled and be determine the load to be handled and be vigilant and take extra care to vigilant and take extra care to limit theselimit these
variations as far as possible.variations as far as possible.
C - LONGITUDINAL C - LONGITUDINAL STSTABILITY LIMITER AND WARNING DEVICEABILITY LIMITER AND WARNING DEVICE
This device gives an indication of the longitudinal stability of the lift truck, and limitsThis device gives an indication of the longitudinal stability of the lift truck, and limits
hydraulic movements in order to ensure hydraulic movements in order to ensure this stabilitythis stability, at least under , at least under the following operatingthe following operating
conditions:conditions:
•• when the lifwhen the lift truck is at t truck is at a standstill,a standstill,
•• when the lift truck is on when the lift truck is on firm, stable and consofirm, stable and consolidated ground,lidated ground,
•• when the lifwhen the lift truck is performing handling and plt truck is performing handling and placing operations.acing operations.
-- Move the jib very carefully when approaching the authorized load limiMove the jib very carefully when approaching the authorized load limit (see: 2 - DESCRIPTION:t (see: 2 - DESCRIPTION:
INSTRUMENTS AND CONTROLS).INSTRUMENTS AND CONTROLS).
-- Always watch this Always watch this device during handlidevice during handling operations.ng operations.
-- In the event that "AGGRAIn the event that "AGGRAVAVATING" hydraulic movemTING" hydraulic movements are cut-off, only perents are cut-off, only performform
de-aggravating hydraulic movements in the following order (fig. C): if necessarde-aggravating hydraulic movements in the following order (fig. C): if necessary, raise they, raise the
jib (1), retract the jijib (1), retract the jib as far as possb as far as possible (2) and lower ible (2) and lower the jib (3) to sthe jib (3) to set down the load.et down the load.
The instrument reading may be erroneous when the steering is at its maximum limit or the rear axleThe instrument reading may be erroneous when the steering is at its maximum limit or the rear axle
oscillated to its limit. Before lifting a load, make sure that the lift truck is not in either of theseoscillated to its limit. Before lifting a load, make sure that the lift truck is not in either of these
situations.situations.
D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK
D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK
Depending on the model of lift truckDepending on the model of lift truck
The transverse attitude is the transverse slope of the chassis with respect to theThe transverse attitude is the transverse slope of the chassis with respect to the
horizontal.horizontal.
Raising the jib reduces the Raising the jib reduces the lift truck’s lateral stability. The transverse attitude must be setlift truck’s lateral stability. The transverse attitude must be set
with the jib in down position as follows:with the jib in down position as follows:
1 - LIFT 1 - LIFT TRUCK WITHOUT SLOPE CORRECTOR USED ON TYRESTRUCK WITHOUT SLOPE CORRECTOR USED ON TYRES
-- Position the lift truck so that the bubblPosition the lift truck so that the bubble in the level is between the two lie in the level is between the two lines (see: 2 -nes (see: 2 -
DESCRIPTION: INSTRUMENTS AND CONTROLS).DESCRIPTION: INSTRUMENTS AND CONTROLS).
2 - LIFT 2 - LIFT TRUCK WITH SLOPE CORRECTOR USED ON TYRESTRUCK WITH SLOPE CORRECTOR USED ON TYRES
-- Correct the slope using the hydraulic Correct the slope using the hydraulic control and verify the horizoncontrol and verify the horizontality via the level. Thtality via the level. Thee
bubble in the level must be between the two bubble in the level must be between the two lines (see: 2 - DESCRIPTION: INSTRUMENTSlines (see: 2 - DESCRIPTION: INSTRUMENTS
AND CONTROLS).AND CONTROLS).
D1D1
D2D2
To Next Page
Loading...
