Manitou MSI25 T 4ST3A - Servicing Schedule

SERVICING SCHEDULE

IMPORTANT

(1): MANDATORY 500 HOUR OR 6 MONTH SERVICE. This service must be carried out after approximately the first 500 hours of operation or within the 6 months following
the start-up of the machine (whichever occurs first).
(2): The engine oil and engine oil filter must be replaced after the first 50 hours of operation and every 500 hours of operation thereafter.
(3): Contact your dealer.
(4): In the event of using diesel fuel with a sulphur content > 5000ppm, halve the filter and engine oil replacement frequency.
A = ADJUST, C = CHECK, G = GREASE, N = CLEAN, P = BLEED,
R = REPLACE, V = DRAIN
PAGE (1)
DAILY OR EVERY 10
HOURS OF SERVICE
EVERY 50 HOURS OF
SERVICE
EVERY 250 HOURS
OF SERVICE
EVERY 500 HOURS
OF SERVICE OR
EVERY YEAR
EVERY 1000 HOURS
OF SERVICE OR
EVERY TWO YEARS
EVERY 2000 HOURS
OF SERVICE OR
EVERY TWO YEARS
EVERY 3000 HOURS
OF SERVICE
EVERY 4000 HOURS
OF SERVICE
OCCASIONAL
ENGINE
- Engine oil level 3-10 C C
- Cooling liquid level 3-10 C C
- Fuel level 3-11
C C
- Cyclonic pre-filter (option) 3-11
N N
- Dry air filter cartridge 3-12/18 R C/N R
- Radiator core 3-12
N N
- Fuel filter 3-16
R N
- Alternator/fan/crankshaft belt tension 3-16 C/A C/A
- Compressor belt tension (Air-conditioning OPTION) 3-17
C/A C/A
- Engine oil (2) (4) 3-18 V V
- Engine oil filter
(2) (4) 3-18 R R
- Fuel filter cartridge 3-19 R R
- Fuel pre-filter * 3-20
R R
- Fuel pre-filter cartridge ** 3-20
R R
- Alternator/fan/crankshaft belt 3-20 R R
- Fuel tank 3-22 N
- Safety dry air filter cartridge 3-22 R
- Engine silent blocks C (3)
- Engine speeds C (3)
- Valve clearances C (3) C (3)
- Cooling liquid 3-26 V
- Injection pump C (3)
- Injectors C (3)
- Radiator C (3)
- Water pump and the thermostat C (3)
- Alternator and the starter motor C (3)
- Turbo compressor * C (3)
- Fuel circuit 3-28 P
* MSI25 T 4ST3A - MSI30 T 4ST3A - MSI35 T 4ST3A - MH25-4 T BUGGIE 4ST3A
** MSI25 36KW 4ST3A - MSI30 36KW 4ST3A - MSI35 36KW 4ST3A - MH25-4 BUGGIE 36KW 4ST3A
TRANSMISSION
- Hydrostatic transmission circuit pressures C (3)
- Hydrostatic transmission control flow C (3)
- Working order of the hydraulic valves for the transmission cut-off and
accelerator
C (3)
TYRES
- Tyre pressures 3-12 C C
- Wheel nut tightening 3-12 C C
- Wheel nut tightening torques 3-26
C C
- Wheel 3-29 R
MAST
- Tension and alignment of the mast lifting chains 3-13 C/A C/A
- Mast 3-13 G G
- Mast lifting chains 3-21
N/C/G N/C/G C (3)
- Condition of mast unit
C
(3)
- Chain rollers
C (3)
- Mast guide rollers
C (3)
- Mast bearing rollers
C (3)
- Thickness of the mast wearing plates
C
(3)
3 - 8
647468 (26/11/2018)
M
SI 25/30/35 ... 4ST3A ; MH 25-4 ... 4ST3A