Need help?Do you have a question about the Marani DPA-260A and is the answer not in the manual?
Input and Output| analog input signal | ChA ChB Bal Female XLR |
|---|---|
| maximum input level | +20dBu |
| analog output signal | Ch Ch Ch Ch Ch Ch Bal Male XLR |
| maximum output level | +20dBu |
Digital Processing| sampling frequency | 48kHz |
|---|---|
| S N | 110dBA |
| frequency response | Bypass Hz kHz dB |
Power and Control| power supply | Switching Power Supply |
|---|---|
| remote control | USB RS 34 |
Ensure proper airflow, avoid heat sources, and keep the unit dry to prevent damage.
Clean with a dry cloth, protect the power cord, and avoid overloading the plug.
Prevent liquids/objects from entering; refer servicing to qualified personnel to avoid shock hazards.
Describes initial power-on, model name display, initialization, and factory pre-set working modes.
Explains the function of encoders (NAV/PAR1, PM2, PM3) and buttons (ENTER, ESC, UTILITY, A/B, 1-6).
Introduces the menu hierarchy and navigation methods for accessing device functions.
Settings for System Setup, Input Routing, Power-On, Delay, Ramps, Software Version.
Allows recalling, saving, and deleting user presets stored in the device memory.
Configures remote control interface and security features like parameter locking and password protection.
Adjusts input channel levels and delay times for channels A and B.
Sets up parametric and shelving filters for input channels, including type, frequency, and gain.
Sets High Pass, Low Pass, and EQ filters for output channels, including type, frequency, and gain.
Configures Vu-meter display, assigns channel names, and adjusts output channel levels.
Describes system setup for different X-over modes (2x2, 2x3, 6 WAY) and input/output assignments.
Explains how to navigate and select options within the UTILITY menu using buttons and encoders.
Details selecting operating modes within the System Utilities sub-menu.
Configures input signal routing (Analog/Digital) and power-on behavior (Fade-In).
Sets measurement units for delay (ms/m) and enables/disables parameter change ramps.
Displays the current software version running on the DPA-260A unit.
Instructions for loading, storing, and naming user presets within the device's memory.
Step-by-step guide for saving edited configurations as named presets.
Procedure for selecting and removing unwanted presets from the device's memory.
Allows selection of the remote control interface protocol, USB or RS485.
Configures parameter visibility when locked and enables/disables unit locking.
Guides the user through entering and confirming a password for device security.
Activates or deactivates the password protection feature, restricting access to functions.
Adjusts input channel levels, delay times, and selects input sources (A/B).
Sets up parametric and shelving filters for input channels, including type, frequency, and gain.
Details configuring Bell filters for input channels, including bandwidth, gain, and center frequency.
Details configuring Low Shelving filters for input channels, including frequency, order, and gain.
Explains how to adjust parameters like Hi Cut Frequency, Order, and Gain for Low Shelving filters.
Details configuring High Shelving filters, including Lo Cut Frequency, Order, and Gain.
Configures HPF for output channels, including frequency, type, and order.
Configures LPF for output channels, including frequency, type, and order.
Details available shapes and orders for Low Pass filters, selectable via the PM3 encoder.
Sets up parametric and shelving filters for output channels, including type, frequency, and gain.
Explains how to adjust parameters like Hi Cut Frequency, Order, and Gain for Low Shelving filters.
Details configuring High Shelving filters, including Lo Cut Frequency, Order, and Gain.
Configures the display on output LED meters to show signal level or limiter activity.
Allows assigning a 6-character name to each output channel.
Selects the input source (Input A, Input B, or sum) for each output channel.
Sets the output channels' level from -12dB to +6dB.
Configures the limiter's attack time, release time, and active threshold.
Sets the delay time for output channels in milliseconds or microseconds.
Sets the polarity for output channels to Normal or Inverted.
Details the HEX commands for recalling presets via USB/RS485 remote control.
Explains HEX commands for modifying input gain and output volume via remote interfaces.
To Next Page