SSttaarrtt HHeerree --
H.O.T. MAGNUM & H.O.T. MAGNUM With BIO-Pro System Quick Setup Guide
1
Parts Check
Canister Prep
A. Canister
1. Lift Cover Lock to Open Canister.
2
.
S
wing Spring Latch downward
a
nd remove Cover.
3. Remove Internal Flow Diffuser
and Center Exhaust Tube.
4. Remove Carbon Media
Container.
B
.
Carbon Media Container
1
.
R
emove Cover and Fill with Black Diamond Carbon.
2. Replace Cover and rinse thoroughly.
3. Slide Rite-Size Filter Sleeve over Container.
4. Replace Container over Impeller Module and Bottom Plate.
5. Replace Exhaust Gasket around Center Exhaust Tube.
6
.
R
eplace Internal Flow Diffuser.
C. F
ill and Seal Canister
1
.
A
dd water until Internal Flow Diffuser is covered.
2. Install Exhaust Gasket onto Cover
.
3. Wet D-Ring with Aquarium Water.
4. Replace Canister Cover. Raise Cover Lock to
e
ngage Spring Latch. Snap Spring Latch in to
g
roove. Push Cover Lock down to close and
s
eal canister.
Placement
DO NOT PLUG IN.
B. Hang Canister in desired position on the
OUTSIDE of aquarium. Adjust Hanger to fit
aquarium frame.
C. Adjust Leveling Clip.
Hanger
Canister
Leveling
Clip
A
.
I
nstall Leveling Clip in slots
at the bottom of Canister.
DO NOT PLUG IN.
Intake/Outlet Assembly
A. Install Intake and Outlet T
ubes. Wet O-Rings on tube ends with aquarium
water. Snap into place by pushing into proper port until Connector Clip
engages and locks. Intake is marked
“IN”, Outlet “OUT”.
NOTE: Adjust Split Flow Dif
fuser Diverter.
Hi-Lo Flow
Side-to-Side Flow
NOTE: Keep water level above
tube “elbow” at all times.
“OUT” “IN”
Split Flow
Dif
fuser Diver
ter
Connector
Clip
Elbow
Intake T
ube
Strainer
CAUTION:
To avoid water spills and
leaks, make sure all connections are
secured where indicated.
NOTE: A slight rattling noise is normal
ONLY DURING STARTUP. If noise persists,
shut off filter and check for dirt or debris
that may be in bottom of Canister.
NOTE:
Drip Loop
(for safety)
Start Up
STOP: If assembling H.O.T. Magnum with (BIO-Pro
System), DO NOT PLUG IN. Continue on to STEP #6
for ADDITIONAL connection directives.
Plug in power cord. Be sure
to create a “Drip Loop”. Press
O
n/Off switch to start filter.
Parts Check
H.O.T
. MAGNUM BIO-Wheel Pr
o System
Cover
BIO-Wheel
Bearings
BIO-Wheel
Assembly
Connector
Clips
Filter
Housing
Spray
Bar
Sliding Nut
and Screw (L-R)
Hose
Barbed Elbow
Adapter
Barbed Elbow Connector
w/ O-Rings
Spray Bar
O-Rings
Snapper
Clamps
Mount & Placement of Filter Housings
A. Check BIO-Wheel Assembly for proper installation. BIO-Wheel should rotate
freely. Also check that the Spray Bar is snapped in place with Connector Clip.
C.
Mount the Filter Housing on the
back wall of aquarium, next to H.O.T.
Magnum canister on Outlet Tube side.
Replace Filter Housing Cover
.
B. Thread the screws through the sliding
nuts on the Filter Housing. (Left and right
nuts are marked. If nuts have slipped off
the housing, reinstall.) Tighten screws so
Filter Housing will not slip.
NOTE:
Remove
Paper insert from
each BIO-Wheel
NOTE:
Do not over tighten
Filter Housing Cover
Connector
Clip
Spray
Bar
NOTE: To remove Spray Bar for cleaning, push
Connector Clip downward (Don’t Squeeze).
Connector
Clip
TO CHANGE FIL
TER MEDIA...
Shut down system and remove Canister
. Carr
y to sink. Remove Cover
.
Change Media. Secure Cover. Return Canister. Restart Filter.
05/07 11957
(800) 322-1266
Questions or Missing Parts?
Call Customer Service at:
www.marineland.com
NOTE: Drip Loop
(for safety)
Start Up
1
1
1
16
4
13
4
15
10
4 5
6 7
CAUTION: To avoid water spills and
leaks, make sure all connections are
secured where indicated.
NOTE:
A slight rattling noise is nor
mal
ONLY DURING STARTUP. If noise persists,
shut off filter and check for dirt or debris
that may be in bottom of Canister.
8
A
ir Ejector
C
leaning
Wand
Squeeze to
open Impeller
Module
Silicone
Lubricant
Switch out Carbon Media
Container with Micron Cartridge
and Rigid Core.
Micron Cartridge
Outside
Rigid Core
Inside
For Periodic W
ater Polishing
or Gravel Washing. . .
Gaskets
Canister Prep
2b
3
A1
A2
A3
Remove
Internal Flow
Diffuser
B1
B2
B3
Replace
Rite-Size
Filter Sleeve
B4
Center
Exhaust Tube
B5
Gaskets
Remove
Center
Exhaust Tub
& Gasket
A4
Remove
Carbon
Media
Container
A2
Remove
Cover & Gasket
B6
Internal
Flow
Diffuser
Cover Lock
Spring Latch
Groove
Connector
Clip
Snapper
Clamps
Connector Assy
.
(Factory Assembled)
Barbed Elbow
Adapter
Barbed Elbow Connector
w/ O-Rings
Connector Assy
.
(Factor
y Assembled)
D.
Snap-Lock Barbed Elbow Connector with
O-Rings into BIO-Wheel Pro and slide Barbed
Elbow Adapter into Outlet Adapter.
Outlet
Adapter
C3
Wet Cover
D-Ring & Replace
C1
C4
On/Of
f Switch
A. Plug in power cord. Be sure
to create a “Drip Loop”. Press
on/off switch to start filter.
B. Adjust BIO-Wheel Spray Bar for
consistent rotation of BIO-Wheel.
On/Off Switch
Spray Bar
NOTE: If assembling H.O.T. Magnum
with the (BIO-Pr
o System), Install
Outlet Adapter BW Pro Tube.
C
leaning
Brush
Elbow
Outlet Adapter BW Pro
NOTE: Keep water level above
tube “elbow” at all times.
NOTE: To remove Tubes Push (don’t squeeze),
Connector Clip downward. DO NOT remove
clip. Slide Intake or Outlet Tubes out of opening
then release Clip.
5
6
7
8
9
14
3
1) Intake Tube, Strainer & O-Ring
2
)
O
utlet Tube, Split Flow Diffuser
& O-Ring
3) Cover, D-Ring Seal &
Connector Clips - 2
4
)
E
xhaust Gasket - 2
5
)
I
nternal Flow Diffuser
6) Center Exhaust Tube
7) Carbon Media Container & Lid
8) Rite Size “U” Foam Sleeve
9) Micron Cartridge & Core
1
0)
B
ottom Plate
1
1)
I
mpeller Module
12) Impeller Assembly
13) Motor, Canister Collar &
Canister Assembly
1
4)
S
pring Latch
15) Hanger
1
6)
L
eveling Clip
12
2
C2
Gaskets
Outlet Adapter
O-Rings
Split Flow Dif
fuser
Connector
Clips
Additional Quick Setup Guide for MAGNUM 350 BIO-Pro System ONLY • Additional Quick Setup Guide for MAGNUM 350 BIO-Pro System ONLY • Additional Quick Setup Guide for MAGNUM 350 BIO-Pro System ONLY
2a
To Next Page
Need help?
General