To Next PageTo Next Page
Need help?Do you have a question about the Marquis SPIRIT and is the answer not in the manual?
Controls the underwater and entryway lights, providing a night light for safety and usability.
Allows cycling through eight different color options for spa lighting.
Activates pump on low/high speed, turns jets off, and controls soak timer.
Starts a 30-minute soak timer, displaying elapsed time and current temperature.
Details the preset filter settings and how to adjust them.
Explains the role of the ozonator in reducing chemical sanitizer needs.
Guide on how to modify filter cycles and duration using control pads.
Lists options for filter cycle frequency and length.
Configuration options for automated filtration cycles based on usage.
How to view and change the spa's water temperature.
Explains the illumination of the HEAT ON light when the heater is active.
Details the Standard, Economy, and Sleep modes for heating.
How to lock control panel settings to prevent accidental changes.
List of components and their quantities for specific spa models.
Details components for Quest and Destiny spa models.
Components list for Reward and Euphoria spa models.
Component breakdown for Silver Anniversary models.
Spa heats to set temperature with periodic water circulation checks.
Spa heats only during filter cycles to conserve energy.
Maintains temperature 20°F below set point, heating during filter cycles.
Instructions for selecting Standard, Economy, or Sleep heat modes.
How to activate and deactivate the system lock feature.
Details sequential activation of pump speeds and jet control.
List of components and their quantities for specific spa models.
List of components and their quantities for Quest and Destiny models.
Components list for Reward and Euphoria spa models.
List of components and their quantities for Silver Anniversary models.
Checks for power issues, diagnostic codes, and circuit breakers.
Steps to ensure proper water flow and jet performance.
Troubleshooting steps for when the spa is not heating.
Solutions for when the spa light fails to illuminate.
Filter cleaning and water change reminders from the control panel.
Troubleshooting for pressure switch, low water, and freeze protection.
Actions for overheat protection shutdown and restart procedures.
Overheat protection and sensor malfunction error codes.
Troubleshooting sensor malfunctions and system shutdowns.
Introduction to the start-up kit and ongoing spa care.
Guide to water treatment regimens and products for clear water.
Program for routine maintenance to extend spa life.
Information on optional accessories to enhance the spa experience.
Differences in spa water care due to temperature and bather load.
Using ozonator and supplemental sanitizers for effective water sanitation.
Importance of alkalinity for pH stability and recommended levels.
Maintaining ideal pH levels for water quality and equipment protection.
Procedure for oxidizing wastes to maintain clear, odor-free water.
Overview of SpaCare products for clear water, ease of use, and peace of mind.
Using the Spa Frog system with mineral and bromine cartridges for sanitation.
Steps to test and adjust pH and alkalinity after filling.
Setting the correct sanitizer residual after balancing.
Using products to prevent metal staining from water supply.
Maintaining correct calcium levels to protect equipment.
Using pH Lock to maintain ideal pH levels for extended periods.
How to set the mineral and bromine cartridges for optimal output.
Step-by-step guide for inserting mineral and bromine cartridges.
Guidelines for storing and disposing of spa chemicals safely.
Maintaining recommended sanitizer levels through regular testing.
Procedure for oxidizing waste products to keep water clear.
Using pH adjusters, clarifier, foam eliminator, and spa perfect.
Diagnosing and fixing cloudy water and odor problems.
Solutions for yellowing water and excessive foam formation.
Using Spa Perfect to break down oils and prevent scum.
Resolving issues with test strips not showing sanitizer levels.
Addressing problems from too much sanitizer and skin irritation.
Troubleshooting metal corrosion and green water/algae.
Dealing with inconsistent pH readings due to high sanitizer.
Definitions for terms related to spa water chemistry and sanitizers.
Definitions for calcium levels and related products.
Definitions related to chlorine chemistry and demand.
Definitions for sanitizers, clarifiers, and foam eliminators.
Definitions for ozonators, pH levels, and pH adjustment products.
Definitions for pH and alkalinity increase/decrease products.
Definitions for ppm, sanitizer types, and shocking procedures.
Definitions for water balance concepts and testing tools.
Instructions for clearing debris from skimmers and suction guards.
Ensuring the spa water is at the optimal two-thirds skimmer level.
Importance of filter cleaning and procedures for removing and cleaning the filter cartridge.
Steps for properly reinserting the cleaned filter cartridge.
Control panel reminder for filter cleaning.
Procedure for draining and refilling the spa to manage water quality.
Checking for leaks around pump seals.
Verifying the ozonator bulb is lit and emitting a green glow.
Schedule for replacing the blue mineral cartridge.
Instructions for cleaning the spa shell using approved agents.
Process for refilling the spa with fresh water and balancing it.
Recommendations for cleaning and conditioning the spa cover.
Cleaning and maintaining the spa's wooden exterior.
Procedure for safely replacing the spa's light bulb.
Steps to take when discontinuing spa use for an extended period.
Underwater lighting system and remote control for spa functions.
Cover lifting mechanisms and customizable jet inserts.
DuraWood steps for access and storage for accessories.
General
