Δ Not Shown.
N/A Not available as replacement part.
* Standard hardware item available locally.
MASTERFORCE Operating Manual and Parts List 241-0818
REPLACEMENT PARTS LIST FOR BENCH GRINDER
11
Ref. Part
No. No. Description Qty.
128118.00Knob 2
2 28120.00 Bushing 6
3 28130.07 Wheel Guard Cover (LH) 1
4 00088.00
5
⁄8”-11 Hex Nut (LH) 1
5 27166.00 Flange 4
6 28257.00 Wire Wheel 1
7 27327.00 Spacer 2
8*
1
⁄4-20 x
1
⁄2” Pan Head Screw 6
9 28129.07 Wheel Guard (LH) 1
10 27180.00 Tool Rest Support (LH) 1
11 27181.00 Tool Rest (LH) 1
12 *
5
⁄16” Flat Washer 6
13 27141.00 Knob 2
14 *
5
⁄16-18 x
1
⁄2” Hex Head Bolt 4
15 *
1
⁄4” Flat Washer 2
16 *
1
⁄4-20 x
1
⁄4” Hex Head Bolt 2
17 27068.00 Spark Guard (LH) 1
18 27047.00 Spacer 2
19 29999.00 6-1.0 x 80mm Carriage Bolt 2
20 27138.00 Eyeshield 2
21 * 6mm Flat Washer 2
22 27046.00 Knob 2
23 28125.00 Wrench 1
24 27086.00 Wheel Dresser 1
25 * #10-24 x
1
⁄4” Pan Head Screw 9
26 27188.00 Support 1
27 N/A Motor Assembly 1
28 27057.00 Sensor Assembly 1
29 05990.00 3-0.5 x 6mm Pan Head Screw 2
30 27056.00 Plate 1
31 28255.00 5-0.8 x 5mm Set Screw 1
Ref. Part
No. No. Description Qty.
32 28254.07 End Bell 1
33 * #10-24 x
3
⁄8” Pan Head Screw 10
34 27048.00 Spark Guard (RH) 1
35 28127.07 Wheel Guard (RH) 1
36 27167.00 Grinding Wheel (60 Grit) 1
37 00087.00
5
⁄8”-11 Hex Nut 1
38 28126.07 Wheel Guard Cover (RH) 1
39 27169.00 Tool Rest Support (RH) 1
40 27170.00 Tool Rest (RH) 1
41 27171.00 Drill Bit Sharpening Plate 1
42 27184.00 Line Cord 1
43 * #10 Serrated Washer 2
44 27060.00 Strain Relief 1
45 27073.00 Plate 1
46 32092.00 Light Assembly 1
47 27076 .07 Sw itch Plat e 1
48 27078.00 Switch 1
49 27079.00 Switch Key 1
50 05474.00 4-0.7 x 6mm Set Screw 1
51 27080.00 Knob 1
52 27185 .07 Base 1
53 27084.00 Pad 4
54 *
1
⁄4” Lock Washer 2
55 *
1
⁄4”-20 Hex Nut 2
56 28262.00 Clamp 1
57 28258.00 Capacitor 1
58 28259.00 Circuit Board Assembly 1
59 27090.00 Tapping Screw 2
60 27083.00 Base Cover 1
Δ * Bulb (S11-Intermediate Base, 120V) 1
Δ 32089.07 Operator’s Manual 1
To Next Page
Loading...
