wiring harness with
4-Way Flat Connectors
MAKKPJIIR\
12V Magnetic LED Tow Light Klt
Model 50015
Instruction Manual & Parts Catalog
Read and understand this entire manual before assembling,
installing, operating, or servicing this product.
SAVE THIS MANUAL
Copyrighte 2016 by Maxx Group, LLC. All rights reserved. No portion of this manual or any artwork contained
herein may be reproduced in any shape or form without the express written consent of Maxx Group, LLC
Due to continuing improvements, actual product may differ slightly from the product described herein. Tools
required for assembly and maintenance may not be included
IMPORTANT SAFETY
INFORMATION
This is a SAFETY ALERT symbol.
It is used to alert you to
potential personal
injury hazards. Obey all
safety messages that follow
this symbol to avoid possible injury or death.
DANGER indicates a
hazardous situation which, if not avoided,
will result in death or injury.
WARNING indicates a
hazardous situation which, if not avoided,
could result in death or serious injury
hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE indicates
important information which, if not followed,
may cause damage to equipment
SAVE THIS MANUAL
Keep this manual for the safety warnings and
precautions The manual offers important infor
mation on how to assemble, use and maintain
this product
Write the product's model number and purchase
date on the cover page of this manual
Keep this manual (and your purchase receipt) in
a safe place
UNPACKING
The shipment should be thoroughly inspected as
soon as it is received. The signed "bill of lad-
ing" is acknowledgement by the carrier of receipt
in good condition or shipment covered by our
invoice. For your own protection, if any of the
goods called for on the bill of lading are shorted
or damaged, do not accept them until the carrier
makes a notation on the freight bill of the shorted
or damaged goods
Notify Maxx Group LLC immediately if any hidden
loss or damage is discovered after receipt.
work properly Press the brake pedal; the
brighter stop lights should turn on while the
pedal is depresed. Check the turn signals;
the blinking turn signal lights should be work-
ing. If any problem is noted, check the Wire
Connection and the circuit that failed. Make
repairs as needed and re-test the lights
8. Placing the 12V Magnetic Tow Lights on
the vehicle:
A. Make sure magnetic surface of Tow
Lights and surface of vehicle is clean. The
underside of each light is magnetic and will
attach to the vehicle's metal surface. To help
avoid surface scratches, do not remove the
protective label on underside of each light
(see photo below)
B. Position Tow Lights
on rear section of
vehicle with RED lights
facing rearward
towards traffic behind
the vehicle. The Tow
Magnetic surface
Light with a green
attachment wire is the right light (curb side)
The other Tow Light (with no green wire)
is the left light and goes on the traffic side.
Make sure the flow of wires is adequate
for turning the vehicle, but not too ong and
loose that it touches the ground
C. Make sure 4-Way Flat Vehicle Connector
and Tow Light Connector are plugged in to
each other.
D. Test the tow lights and vehicle lights to
make sure both are working properly:
- both Tow Lights should be on when tow
vehicle's running lights are on.
-when brake is applied, both Tow Lights
should brightly light up
-when the tow vehicle's left and right turn
signals are activated, the appropriate Tow
Light should also blink brightly
Definition of Symbol
WARNING concerning Risk of Eye
Injury. Wear ANSI approved eye
protection.
WARNING concerning Risk of
Hearing Loss. Wear hearing pro-
tection
IMPORTANT SAFETY
INSTRUCTIONS
MANOAL
afet warnin s and instru
tigns. Failure to follow the warnings and in
structions may result in serious injury or death
Save all warnings and instructions for future
reference
2. eersgnaLand—gr.K-Ar.e.aSafety
Always wear ANSI approved
safety goggles.
Always wear hearing protec-
tection when working in noisy
environments. Prolonged exposure to high
intensity noise can cause hearing loss
c
Use safety equipment. Safe-
ty shoes, hard hat and work
gloves must be used for applicable conditions.
D Dress appropriately. Never wear loose fit
ting clothing or jewelry when working Contain
long hair, and keep hair, clothing and gloves
away from moving parts. Remove conductive
objects such as metal jewelry and watches be
fore installing the light kit.
E Use common sense when working. Stay
alert and concentrate when setting up and using
the 12V Magnetic Tow Light Kit. Never work
while under the influence of alcohol, drugs or
medications
F While assembling and using the 12V Magnet
ic Tow Light Kit keep work area clean and well
lighted. Keep spectators and children out of the
work area
3. Use of the 12V Magnetic Tow Light Kit
A. This 12V Magnetic Tow Light Kit is de-
signed for trailers less than 80 inches in
width Only install these lights on a 12V
negative ground circuit. The tow light kit is
not waterproof; do not install on boat trailers
or other marine applications. Adhere to all
Department of Transportation (DOT) stan-
dards and regulations regarding light kits
Do not modify the Tow Light Kit and do
not use this product for purposes that it
was not designed for.
B. As pertaining to lights on trailers, read
and adhere to all safety guidelines and in-
structions provided by the manufacturer
of the trailer.
C. If you are not experienced in assembly-
ing and setting up electrical products such
as this one, the work should be done by a
qualified service technician.
D. Keep children and spectators well clear
when setting up this product and when ma-
neuvering a towed vehicle
E People with pacemak-
ers should consult their physician(s) before
using this product. Operation of electrica
equipment in close proximity to a heart pace
maker could cause interference to, or failure
of, the pacemaker.
F. To verify that the correct wire has been
located on the tow vehicle's wiring harness,
it is recommended that a circuit tester be
used
G The vehicle/trailer must be stationary
when Tow Lights are installed. Vehicle's en
gine must be OFF and parking brake set.
H. Only set up lights with red lights facing
backward (towards traffic behind)
Test the operation of the lights before driving
in traffic. Once Tow Lights are in operation,
periodically pull over and check the position
and operation of the lights Wind and road
conditions can affect the position of the lights
Make sure that the lights remain securely
in position.
Keep in mind that the warnings, cautions,
and instuctions previously discussed
cannot cover all possible events and cir-
curnstances. It is important that the per-
son setting up and using this product use
common sense and caution at all times.
Maxx Group LLC is not responsible for the
attachment or the installation of this prod-
uct. The attachment of this product is
critical and beyond the control of Maxx Group
LLC Towing Products. Failure to follow
all instructions and safety warnings can
result in an accident, injury and/or prop-
erty damage. Maxx Group LLC neither guaran-
tees, nor will it be liable for any damage
resulting from the 12V Magnetic Tow
Light's attachment or improper use.
Limited Warranty
Maxx Group LLC warrants to the original retail
purchaser that the product is free of defects
in material and workmanship at the time of
shipment This Light Kit is warranteed for 90
days from the date of purchase This war
ranty is expressly in lieu of all other warran
ties, express or implied
Proof of purchase is required for warranty
transactions; a copy of the original invoice
Model 50015
page 2
or sales receipt is required
Model 50015
page 3
Assembling and Setting Up
the 12V Magnetic LED Tow Light Kit
wiring harness with
Tow Light
4-Way Flat Connectors
Wire Connectors
Model 50015 shown
I. Refer to photo above of all components
included in the kit.
Always wear ANSI approved
safety goggles.
2. Refer to the photo below when planning
and setting-up the 4-Way Flat Vehicle Connec-
tor to the towing vehicle's wiring
Wire ends connect
totowingvehicle'sN
electrical wiring
4-Way Flat
Vehicle Connector
3. If the towing vehicle already has a 4-Way
flat connector trunk plug, the wiring instructions
below will not be needed
4. To connect the towing vehicle wiring to the
4-Way Vehicle Connector, you must first iden-
tify the towing vehicle's wires and determine
where they connect to the wires of the 4-Way
Flat Vehicle Connector (shown above)
The WHITE wire of Vehicle Connector is a
ground wire and is attached to a clean, bare
metal surface of the towing vehicle.
The BROWN wire connects to the running
lights wire of the tow vehicle.
The YELLOW wire connects to the tow ve-
hicle's left stop, and turn light wire.
The GREEN wire connects to the tow vehicle's
right stop and turn light wire.
5. These wires can be connected together
by using Wire Connectors. See instructions
below:
A. Insert the end of the wire from the 4-Way
Flat Vehicle Connector into the wire channel
that is blocked off on one end
B. In the open wire channel, place the corre
sponding wire from the vehicle.
Wire from 4-Way
Flat Vehicle Connector
Wire from tow vehicle
C. Slowly close the cover of the Wire Connec-
tor, making sure that the wires remain in the
channels. Cover will snap in place. See photo
below.
Make sure that
wires are
held in place
6. With the tow vehicle's electrical wiring now
connected to the 4-Way Flat Trailer Connec-
tor, this connector can now be plugged into the
4 Way Flat Tow Light Connector
7. Test the lights. Turn on the tow vehicle's
head lights. With a spotter to assist, check that
the Tow Lights and the tow vehicle's lights all
E. With this successful test, the Tow Lights
are ready and will activate when running
lights, turn lights and brake lights are acti-
vated on the tow vehicle.
F. While in use, frequently stop and check
the Tow Lights Extreme weather and rough
road sufaces can impact the magnetic con
nection of the Tow Lights to the vehicle
SPECIFICATIONS
For Model 50015
Electrical Source
Included Components
Product Application
Model
12 Volt DC 1 Negative
Ground
4-1/2" Red Brake Lights
20' Wiring Harness with
standard 4 pin connec-
tors
Color coded wiring
Wire Connectors
For towing applications
up to 80" wide vehicles
Model 50015
Page 4
50015
Page 5
To Next Page
Need help?
General
