ON-BOARD DIAGNOSTIC [SJ6A-EL]
05–02–3
05–02
MIL: Malfunction Indicator Lamp
DC: Drive Cycle
End Of Sie
MEMORY FUNCTION [SJ6A-EL]
EHU050200000104
• The memory function stores malfunction information detected in the malfunction detection function. Once
malfunction information is stored, the memory will not be cleared even when the ignition switch is turned off
(LOCK position) or the malfunction is repaired.
• The stored memory (malfunction information) can be cleared using the WDS or equivalent, or by disconnecting
the negative battery cable.
End Of Sie
MALFUNCTION INDICATION FUNCTION [SJ6A-EL]
EHU050200000105
• The malfunction indication function illuminates the MIL or AT warning light when the malfunction detection
function determines there is a malfunction.
End Of Sie
FAIL-SAFE FUNCTION [SJ6A-EL]
EHU050200000106
• In the fail-safe function, minimum vehicle drivability is obtained by changing the signals that are determined to
be malfunctions by the malfunction detection function to the preset values, and limiting TCM control.
P2719 Shift solenoid G range/performance (stuck) X X 1 X
P2720 Shift solenoid G circuit malfunction (short to ground/open circuit) X X 1 X
P2721 Shift solenoid G circuit malfunction (short to power) X X 1 X
P2757 Torque converter clutch (TCC) stuck off X X 2 X
P2758 Torque converter clutch (TCC) stuck on X X 2 X
P2762 TCC control solenoid range/performance (stuck) X X 1 X
P2763 TCC control solenoid circuit malfunction (short to power) X X 1 X
P2764 TCC control solenoid circuit malfunction (short to ground/open circuit) X X 1 X
U0073 CAN BUS OFF X X 1 X
U0100 TCM cannot receive any signals from PCM X X 1 X
U0121 TCM cannot receive any signals from ABS HU/CM or DSC HU/CM X X 1 X
DTC No. Condition MIL
AT
warning
light
DC
Memory
function
DTC
No.
On-board diagnostic
function
Detection condition Fail-safe
P0601 Flash ROM malfunction
• Flash ROM (in TCM) internal circuit
malfunction is detected.
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
• Inhibits slip control
P0603 EEPROM malfunction
• Different numeric values for
EEPRROM and RAM (in TCM) are
detected.
N/A
P0604 RAM malfunction
• RAM (in TCM) read/write error is
detected.
• Emergency mode
• Inhibits self learning control
• Inhibits driver adaptive shift control
• Inhibits TCC control
• Inhibits slip control
P0707
Transmission range (TR)
switch circuit low input
(short to ground)
• TR switch position voltage input to
TCM is less than 0.127 V when
ignition switch is at ON position.
• D range is determined when there is no
TR switch signal input.
• Inhibits slope mode control
P0708
Transmission range (TR)
switch circuit high input
(open circuit)
• Vehicle speed is 30 km/h {18.6 mph}
or more, and no range signal is input
from the TR switch.
• D range is determined when there is no
TR switch signal input.
• Inhibits slope mode control
P0711
Transmission fluid
temperature (TFT) sensor
malfunction (stuck)
• Change in ATF temperature cannot be
detected for 10 min or more when
driving in D range.
• Fixes ATF temperature value at 80 °C
{176 °F}
• Inhibits slope mode control
• Inhibits self learning control
• Inhibits slip control
To Next Page
Loading...
