Need help?Do you have a question about the McConnel PA 48 and is the answer not in the manual?
Details on dealer responsibilities for registering machine warranty.
Instructions for the customer to ensure warranty registration is completed.
Manufacturer's statement that the product meets EEC Machinery Directive requirements.
Lists standards supporting the directive and its implementation in UK law.
Details on measured noise exposure at the operator's ear in different conditions.
Explains key terms like WARNING, CAUTION, NOTE, and hand orientation.
Instructions for recording machine serial number and dealer details.
General specifications for all PA48 series models.
Specific details for SI, TI, and TI electric models.
Lists major hazards associated with the machine's operation.
Lists mandatory checks and actions before operating the machine.
Specific safety advice for working near overhead power lines.
Lists conditions and situations where the machine should not be operated.
Advice on operator competency and safety when working in public areas.
Guidelines on using warning signs and safe road working practices.
Requirements for tractor cabs, guards, and the importance of vehicle ballast.
Factors affecting stability and methods to increase it.
Specifies tractor linkage, PTO shaft, and hydraulic system requirements.
Guidance on fitting the operator guard and setting wheel width.
Instructions for adding ballast weight and adjusting lift links.
Details on installing the control valve conversion kit for SI models.
Recommends specific oils for the tank and gearbox based on climate.
Steps for preparing the machine upon delivery.
Detailed procedure for connecting the machine to the tractor.
Instructions for securing the yoke and measuring the PTO shaft.
Guidance on operating controls and making final adjustments during attachment.
Steps for removing arrestors, parking feet, and checking hoses.
Procedure for folding the machine into transport position.
How to connect and mount the electric control unit in the tractor cab.
Guidelines for mounting cable control units and managing cable bend radii.
Specific running-up steps for TI and SI model machines.
Schedule for replacing return filter elements for all models.
Critical order of steps for removing the machine from the tractor.
Advice on storing the machine, including protection for control units.
Specifies the maximum material thickness for PA9058 and PA93 models.
Information on operator guard and advice for practicing controls.
Diagram and explanation of cable control levers for SI and TI models.
Diagram and explanation of electric switchbox controls.
How to select and use the optional head angle float position.
Diagram and explanation of electric monolever control joystick.
Diagram and explanation of proportional electric control joystick.
How to select and use the optional head angle float on electric models.
Operation of rotor ON/OFF using the tractor's PTO lever for SI models.
Operation of rotor ON/OFF using a control lever for TI models.
Steps to secure the machine for highway transport.
Procedures for engaging the PTO and rotor drive for different models.
Recommended operating speeds for the rotor and tractor.
Requirement to observe local highway working regulations.
Always follow safe working practices, check guards, and keep bystanders clear.
Explanation of the automatically resetting breakaway system.
Procedure for safely removing wire caught in the rotor.
Caution regarding overhead obstacles, especially power cables.
Inspecting the work area and setting rotor direction for cutting.
How to perform upward and downward cutting, and required hoods.
Procedures for changing rotor rotation direction on SI and TI models.
Requirement for flails to cut upwards during grass cutting.
Diagrams showing positions for bushed and ball bearing rollers.
Important warning against mounting the ball bearing roller in position 'B'.
Illustrates the sequence of operations for cutting hedges.
How to engage the lift float, and its effect on weight distribution.
How the angle float facility allows the head to follow ground contours.
Details on daily greasing points and weekly lubrication of PTO shaft.
Daily oil level checks and methods to reduce contamination.
Information on suction strainers and return line filter maintenance.
Inspecting flails, bolts, and procedures for sharpening.
How cables operate, installation care, and why lubrication is not needed.
Checking hose condition, replacement procedures, and warranty limitations.
How to check gearbox oil level and when to change it.
Identifies supply, return, and other ports on the cable model control valve.
Identifies ports on the electric model control valve.
Diagram of the rotor control valve for totally independent machines.
Diagram of the rotor relief valve for semi-independent machines.
Details on fitting the debris blower bracket and important notes.
To Next Page
General