Need help?Do you have a question about the Microbit RRC-1258 MkII(s) and is the answer not in the manual?
General| Brand | Microbit |
|---|---|
| Model | RRC-1258 MkII(s) |
| Category | Remote Control |
| Language | English |
How the system works with radios featuring detachable control panels.
High-end solution for DX-ers and contesters using Elecraft K3 and Yaesu.
Pinout for the RS-232 interface on the front panel.
Usage of the TTL connector for control panels and TTL level signals.
Pinout for the AUX (RJ45) connector for TTL control.
Usage of the TTL connector for radio communication and CAT control.
Details of the speaker output connector on the Control-RRC.
Input for speaker signals from the radio to the Radio-RRC.
CW speed adjustment using the knob on the Control-RRC.
COM2 connector for PC connection via RS-232.
COM2 connector for radio connection via RS-232.
Pinout for the RS-232 interface for radio connection.
Connecting a CW-paddle to PAD connectors on Control and Radio RRC.
Power consumption details for different radio models and RRC units.
Pin configuration for the PWR connector (10-18 VDC).
How to reboot or reset the unit to factory default settings.
I/O connector for signal transfer, inputs/outputs, and CW-keyer signals.
Pinout for the Ethernet port and LED indicators for link and activity.
Strapping for the AUX/MIC connector based on radio models.
JMP-1 placement for feeding DC voltage to microphone elements.
JMP-2 selection for 8V or 9V DC power to front panels.
JMP-3 to connect RTS and CTS together for RS-232 port.
JMP-4 selection for speaker or headset level for Main-Rx output.
JMP-5 decision for grounding pin 1 in the TTL connector.
Overview of functions like IP settings, firmware upgrades, and profile changes.
Viewing the firmware and bootloader versions using the Setup Manager.
Steps for downloading and updating the RRC firmware via the Setup Manager.
Reading current IP settings using the 'Get' button in Net info.
Description of WiFi tab and note on Serial port tab usage.
Using `ipconfig` in CMD to determine PC's network configuration.
How to select, edit, submit, and apply changes through the web interface.
Updating the bootloader firmware using steps similar to application firmware upgrade.
Resetting and restarting the RRC without saving changes or for ordinary reset.
Steps for selecting WiFi tab and initiating connection setup.
Pin assignments for CW-keyer signals via I/O connector.
Hardware configuration and jumper settings for ICOM CI-V radios.
Example radio settings for ICOM CI-V radios.
Example radio settings for ICOM IC-7100.
Necessary signals and cable connections for IC-7100.
Example radio settings for ICOM IC-703/706.
Cable connections and preparation for IC-703/706.
Cabling and use of HM-133 adapter boards for IC-E2820.
Jumper settings and cable connections for ICOM ID-E880.
Using HM-133/880 adapter PCBs for ID-E880 microphone function.
Hardware adaptation for IC-2725 serial bus and adapter PCBs.
Radio settings and cable connections for IC-2725.
Hardware configuration and small PCB strapping for Yaesu Twin package.
Example radio settings for Yaesu Twin.
Hardware configuration and strapping instructions for FT-857.
Example radio settings for Yaesu FT-857.
Example radio settings for Yaesu FTM-350.
Example radio settings for Yaesu FT-7800/8800/8900.
Cable connections and using adapter cables for FT-8x7 series.
Radio settings and cable connections for Yaesu FT-2000.
Hardware configuration and jumper settings for Kenwood TS-480.
Example radio settings for Kenwood TS-480.
Different hardware configurations for Kenwood TS-480 based on serial number.
Example radio settings for Kenwood TS-480.
Example radio settings for Kenwood TM-D710.
Example radio settings for Kenwood TM-D700.
Example radio settings for Kenwood TS-2000.
Cable connections and preparation for TS-2000.
Hardware configuration and small PCB strapping for Elecraft K3 Twin.
Example radio settings for Elecraft K3 Twin.
Example radio settings for Elecraft radios.
Cable connections for Elecraft radios.
Hardware configuration for Alinco DX-SR8/DX-R8.
Example radio settings for Alinco DX-SR8/DX-R8.
Example radio settings for 2-wire and 4-wire interfaces.
Pinout for AUX/MIC connector for 2-wire and 4-wire interfaces.
Device compliance with FCC Rules Part 15 and measures to correct interference.
Warnings about water, electrical storms, high volume audio, and power supply limits.
To Next Page