3Microlife NC 150
EN
steady. The unit is ready for the next measurement as soon as
the «°C» or «°F» icon is flashing again.
Low battery indicator AO: When the unit is turned on, the «»
icon will keep flashing to remind the user to replace the
batteries.
5. Setting Date, Time and Beeper Functions
Setting the date and time
1. After the new batteries are fitted, the year number flashes in the
display BP. You can set the year by pressing the START button
4. To confirm and then set the month, press the M-button 8.
2. Press the START button 4 to set the month. Press the M-
button 8 to confirm and then set the day.
3. Follow the previously mentioned instructions to set the day, 12
or 24 hour mode, hours and minutes.
4. Once you have set the minutes and pressed the M-button 8,
the date and time are set and the time is displayed.
Setting the beeper
1. When the device is switched off, press and hold the ON/OFF
button 5 for 5 seconds to set the beeper BQ.
2. Press the ON/OFF button 5 again to either turn the beeper on
or off. The beeper is activated when the beeper icon BQ is not
crossed-out.
6. Changing between Body and Object Mode
For changing from body to object mode, slide the mode switch 6
at the side of the thermometer downwards. For switching back to
body mode, slide the switch up again.
7. Directions for Use
Measuring in body mode
1. Press the ON/OFF button 5. The display 3 is activated to
show all segments for 1 second.
2. When the «°C» or «°F» icon is flashing, a beep sound is heard
and the thermometer is ready for measuring AK.
3. Aim the thermometer at the center of the forehead with a
distance of no more than 5 cm. Please remove any hair,
sweat or dirt from the forehead before measuring to improve the
accuracy of the readings.
4. Press the START button 4 and ensure that the activated
blue tracking light is aimed at the center of the forehead.
After 3 seconds a long beep will verify the completion of
measurement.
5. Read the recorded temperature from the LCD display.
Measuring in object mode
1. Follow steps 1-2 above, then aim the thermometer at the center
of the object you want to measure with a distance of no more
than 5 cm. Press the START button 4. After 3 seconds a long
beep will verify the completion of measurement.
2. Read the recorded temperature from the LCD display.
Patients and thermometer should stay in similar room
condition for at least 30 minutes.
Don't take a measurement while or immediately after nursing a
baby.
Don't use the thermometer in high humidity environments.
Patients should not drink, eat or exercise before/while taking
the measurement.
Don't move the measurement device from the measuring area
before hearing the termination beep.
10 short beeps and a red LCD backlight alert the patient that he/
she may have a temperature equal to or higher than 37.5 °C.
Always take the temperature in the same location, since
temperature readings may vary according to locations.
Doctors recommend rectal measurement for newborn infants
within the first 6 months, as all other measuring methods might
lead to ambiguous results. If using a non contact thermometer
on those infants, we always recommend verifying the readings
with a rectal measurement.
If no button is pressed for 20 seconds, the device automat-
ically switches to ready for measuring AK.
Cancel time setup: Press the ON/OFF button 5 during
time setup. The LCD will show Date/Time icons with «--:--».
After that press the ON/OFF button 5 to start the measure-
ment. If no further action is taken within 20 seconds, the
device will automatically turn off.
Change current date and time: Press and hold the M-
button 8 for approx. 3 seconds until the year number
starts to flash BP. Now you can enter the new values as
described above.
If no button is pressed for 5 seconds, the device
automatically switches to ready for measuring AK.
NOTE:
To Next Page
Loading...
