Chapter 7 Appendix
7-2
Specifications
Printer Section Specifications
Cutter Section Specifications
Item CJV150-75 CJV150-107 CJV150-130 CJV150-160
Print head
Method Drop-on-demand piezoelectric print heads
Specification 1 head staggered
Printing mode (scan x feed) 360×360dpi/ 540×360dpi/ 540×720dpi/ 720×1080dpi/ 720×1440dpi/ 1440x1440dpi
Usable inks
Solvent ink (SS):
10 colors (Y,M,C,K,
Lc,Lm, Or, Lk, Si, W)
Solvent ink (ES):6
colors (Y, M, C, K, Lc,
Lm)
Sublimation dye ink (Sb):6 colors (Y,M,Bl,K or Dk,LBl,Lm)
Solvent ink (SS):10 colors (Y,M,C,K, Lc,Lm, Or, Lk, Si, W)
Solvent ink (ES):6 colors (Y, M, C, K, Lc, Lm)
Ink supply
Supplying from ink cartridges through tubes.Ink cartridge replacement type :
Supplying by Toggle switch over with 2 cartridges/color (4-colors ink set)
Capacity of ink cartridge
M, C, Y, K, Lm, Lc, Or, Lk : 440cc cartridge
W, Si : 220cc cartridge
Usable media
label stock (paper-based) / PVC sheet (including laminated; thickness no more than 0.25 mm)
/ Reflective sheet (excluding high-luminance reflective sheet) / Heat transfer rubber sheet
Margin
Leaf media Left end and right end : 15 mm (Default) Front :120 mm Rear : 150 mm
Roll media Left end and right end : 15 mm (Default) Front :120 mm Rear : 150 mm
Head height adjustment
Select for manual 3-stage (2.0/2.5/3.0) + 1 mm or + 2 mm at installation. Base height can be
raised.
Waste ink tank Bottle type ( 2,000 cc)
Interface USB 2.0 (Ethernet 10 BASE/ 100 BASE E-mail function)
Command MRL- IV
Item Specifications
Maximum speed
*1
*1. The maximum speed may be limited, depending on the size of a used medium. In addition, the cutting section does not operate with both speed and
acceleration being at the maximum.
30cm/s
Maximum acceleration 1G
Cutting pressure 10 to 450g
Usable tools
Eccentric cutter/ water-based ballpoint pen/ oil-based ballpoint pen/
Ballpoint pen for handwriting (sold on the market)
*2
*2. Use one with a diameter of 8 to 9 Φ whose clamped part has no protrusion or taper. In addition, because the position of the pen point changes, depending on
the types of pens, no good image quality can be ensured.
Number of times the cutter responds
to a medium
10 times/sec
Usable media
Polyvinyl chloride sheet (Thickness of 0.25mm or less with laminate
*3
)/ fluorescent
sheet
*4
/ reflecting sheet
*4
(excluding high-intensity reflecting sheets)/ Label card
(paper-based)/ Heat transfer rubber sheet
*3. This conforms with our specified sheet.
*4. When a blade dedicated for fluorescent sheets (SPB-0007) or a blade dedicated for reflecting sheets (SPB-0006) is used.
Margin
Leaf media
Left and right: 15mm (default value), Minimum : 5mm
Front :135 mm Rear : 150 mm
Roll media
Left and right: 15mm (default value), Minimum : 5mm
Front :135 mm Rear : 150 mm
Repetition accuracy
*5
*5. For repetition accuracy, see the lower part of this page.
±0.2 mm or the ±0.1% of the specified distance, whichever is larger.
Reception buffer memory 256 MB
Command MGL-II c2
Program step 25μm
To Next Page
Loading...
