4-11
4
2
2
perform multiple Cut-
tings (Copy function)
This function performs cutting for the received data on two
or more sheets.(Maximum 999 cuttings)
• You can perform multiple cuttings by specifying data saved in
the receiving buffer of this device.
• The receiving buffer can save only one data.
• When a new data is received, the data that has been saved is
overwritten by it.
(You cannot perform multiple cuttings by specifying the data
that was received before.)
1
Press the
(MENU)
(>>)
key in LOCAL.
• Cuttibg MENU will be displayed.
2
Press 3 times, and then press the
key.
• “COPY” will be selected.
3
Press to select the number of
cutting (1 to 999)), and then press the
key.
4
Press to select the interval of
figures to be cut (0 to 30mm), and then
press the key.
SETUP SUB MENU
The SETUP SUB MENU offer convenient functions that
you can use in cutting.
The following items are available in the sub menus.
Setting the DIVISION CUT
When you set DIVISION CUT for the width direction (y),
you can cut the data bigger than the media width by
dividing it.
In addition, when you set DIVISION CUT for the feeding
direction (X), you can cut the long data by dividing it and
you can prevent cutting misalignment due to media
meandering.
Set the Y direction (width direction)
DIVISION CUT
1
Press the
(MENU)
(>>)
key in LOCAL.
• Cuttibg MENU will be displayed.
2
Press
(>>)
and then press the
key.
• “SETUP SUB MENU” will be selected.
• If the multiple sheet cutting is executed
immediately after cutting in the remote mode,
cutting (plotting) will be overlapped. To avoid this
trouble, be sure to set the new origin.
• While the plotter is executing the multiple sheet
cutting, it ignores data sent from the computer.
• To send two or more pieces of data from the
computer to the plotter, the data has to be sent
while providing an interval of 5 seconds or more
between any two pieces of data. If two pieces of
data are sent from the computer to the plotter
within 5 seconds, the two pieces of data will be
subjected to the multiple sheet cutting. The plotter
performs cutting for divided cutting data by the
specified number of sheets without dividing the
data. If any error is displayed, refer to “Error
messages” ( P.6-8).
• If there is the origin renewal command in cutting
data, you cannot perform copy function.
• When you use FineCut, the default value of Origin
Renewal is “ON”. If you perform [No. COPIES],
uncheck the checkbox. (Refer to FineCut
OPERATION MANUAL Chapter5 “Setting Head
Position after Plotting”)
Copy
interval
The origin at
executing the multiple
sheet cutting. (Manual
The origin at
terminating the
multiple sheet cutting
Function name Outline
DIVISION CUT
(P.4-11)
You can cut the data bigger than the sheet
width by dividing it.
With division cut, you can make settings for
the width direction (Y) and feed direction
(X).
UP SPEED
(P.4-13)
This is to set the speed of sheet and
carriage movement when the tool is up.
Setting the speed lower makes the sheet
misalignment reduced at the time of long
sheet feeding.
DUMMY CUT
(P.4-13)
You can the blade edge is made to turn to a
specific direction before starting cutting,
which allows dummy cutting.
SHEET TYPE
(P.4-13)
This is to set the types of sheet according
to the sheet you use.
ADJ PRS
OFFSET
(P.4-13)
This is used to expand the value in such a
case as when the beginning and end part
of the cut are left cut.
OVER CUT
(P.4-13)
By over lapping the start point and the end
point arbitrarily, you can make the media
without uncut area.
SETUP RESET
(P.4-14)
Reset the setting values to the initial state.
With the DVISION CUT function, you can use the
following convenient functions too.
• Perform a frame cut:
Together with the cut data, the plotter
automatically cuts out the frame fitted to the size of
the cut data.
• Put a mark for leaving a margin for gluing:
You can put a “mark” for showing the point for
gluing together the DIVISION CUT medias.
To Next Page
Loading...
