MIMAKI SWJ-320EA - Page 86

4-14
Chapter 4 Maintenance
6
Press the key twice.
• Printing of the nozzle pattern will start.
• Select “ENTRY” then “Move to select of the
Nozzle line (Step 5) without drawing a pattern”
7
Select the Nozzle line that needs Nozzle
Recovery by pressing , and
press key.
8
Register the Nozzle number that needs
Nozzle Recovery and then press
key.
(1) Select the registration number from 1 to 10
by pressing [][] key and press the
[ENTER] key.
(2) Register the nozzle number that needs
recovery by pressing [][] key and press
the [ENTER] key.
9
Press the key several times
to end the setting.
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
241
250
261
270
281
290
301
310
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
241
250
261
270
281
290
301
310
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
241
250
261
270
281
290
301
310
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
241
250
261
270
281
290
301
310
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
241
250
261
270
281
290
301
310
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
241
250
261
270
281
290
301
310
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
241
250
261
270
281
290
301
310
1
10
2
30
4
50
6
70
8
90
1
110
1
130
1
150
1
170
1
190
2
210
2
230
2
250
2
270
2
290
3
310
Overhead view (4-colors inkset)
H1-A H1-D H2-A H2-CH1-B H1-C H2-B H2-D
• Set a media of more than 210mm put horizontally.
If a media with narrow width is set, printing will
only be conducted to midway.
Nozzle pattern of Head 1 and 2(4-colors inkset)
SELECT ENTRY NOZZLE
H1-A
>
> H1-B
>
H1-C
>
H1-D
>><<
>
＊＊＊＊
Head No.
(H1 to H2)
Nozzle line
• Up to 10 nozzles can be registered per 1 nozzle
line.
• Even if you use this function, time required for
drawing does not change.
• The nozzle recovery is not reflected if printing is
performed under the following conditions:
Head1-A
No.1
No.2
16
128
No.3
184
No.4
OFF
No.5
OFF
>><<
Recovery nozzle No. or OFF
Registration number : 1 to 10
Nozzle missing
No.184
Nozzle number
Nozzle missing No.16
Nozzle missing
No.128
Registration
number
Recovery
Nozzle No.
State
1 16 Target for nozzle recovery
2 128 Target for nozzle recovery
3 184 Target for nozzle recovery
4 OFF No registration
5 OFF No registration
Example of nozzle to be recovered
Resolution Pass Scan speed
300x600 2 pass Normal