Mitsubishi Electric MELSEC iQ-F Series - Page 71

5 Replacement from FX3U to FX5U
5.3 Selection of Substitute Models
69
5
•FX5U
■Cable sizes for European type terminal block
Suitable wiring and tightening torque are described below.
■Differences and precautions regarding installing the FX3U and FX5U
The FX3U and FX5U CPU modules have the same vertical and horizontal sizes, but the pitch of the installation holes in a
horizontal control panel will differ depending on the model name of the FX5U switched to. When making a direct installation in
a control panel, installation holes must be added. Also, because the terminal block shapes differ, one terminal block cannot be
replaced with the other. ( Page 68 External dimension drawing)
■Differences and precautions regarding the drive power supply of the output section of the
FX3U-16M and FX5U
• Output section power supply consolidation
When replacing the FX3U-16M with the FX5U, the power supplies must be consolidated if a separate power supply has
been installed with the common terminal of the FX3U-16M.
• Maximum output load current
When the FX3U-16M is replaced with the FX5U, the maximum load current of the output section changes.
If separate power supplies have been installed with each common terminal, consolidate the power supplies.
External color: Munsell 0.6B7.6/0.2
Unit: mm
The terminal block uses M3 terminal
screws
35 mm width DIN rail can be
installed
Model name W: mm W1: mm Weight: kg
FX5U-32M 150 123 Approx. 0.70
FX5U-64M 220 193 Approx. 1.00
FX5U-80M 285 258 Approx. 1.20
Wire size for
one wire
Wire size for
two wires
Wire ferrule with
insulation sleeve
(wire size)
Tightening
torque
Stripping dimensions of
electric wire ends
Built-in RS-485 communication
terminal block
Built-in analog I/O terminal block
AWG24 to
AWG20
AWG24 AWG24 to AWG20 0.22 to 0.25
Nm
5 mm
FX3U-485-BD, FX3U-485ADP(-MB) AWG22 to
AWG20
AWG22 AWG22 to AWG20 0.22 to 0.25
Nm
9 mm
FX5-485-BD, FX5-485ADP
FX5-4AD-ADP, FX5-4DA-ADP, FX5-
4A-ADP, FX5-4AD-PT-ADP, FX5-
4AD-TC-ADP
0.20 Nm
(Example) FX3U-16MT/ES (output side) (Example) FX5U-32MT/ES (output side)
<Number of outputs per common>
• 1 common terminal per output
<Maximum output load current>
• Maximum load (resistance load) current of 1 output common
terminal: 0.5 A or less
<Number of outputs per common>
• 1 common terminal per 3 or 4 outputs
<Maximum output load current>
• Maximum load (resistance load) current of 4 output common terminal
0.8 A or less
• Maximum load (resistance load) current of 8 output common terminal:
1.6 A or less
W1 (mounting hole pitch)22
80 (mounting hole pitch)
90
W83
8
2-φ4.5-diam mounting hole (32M)
4-φ4.5-diam mounting hole (64M, 80M)
There is no mounting hole * for 32M.
*
*
Y2Y0 Y1
COM 1 COM2COM0 COM3
Y3
COM4 COM5 COM6 COM7
Y5 Y6 Y7Y4
2Y0
1
COM1COM0 3 COM2 COM3 5
Y1412Y10 16
1713 15117
Y4 6