778
APPX
Appendix 1 Error Codes
4803H iQ Sensor
Solution related
error
• The system file does not exist in the specified backup data,
or the system file is corrupted.
• Specify another backup data.
4804H iQ Sensor
Solution related
error
• The backup file does not exist in the specified backup data,
or the backup file is corrupted.
• Specify another backup data.
4805H iQ Sensor
Solution related
error
• When the iQ Sensor Solution data backup function is
executed, no backup target device exists.
• The data backup function was executed to a device which
does not support the function.
• Check and correct the value in the special register (SD), and
execute the function again.
• Execute the function to a device which supports the function.
4806H iQ Sensor
Solution related
error
An SD memory card is in the following state while the function
is being executed.
• An SD memory card is not inserted.
• An SD memory card is disabled by SM606 (SD memory card
forced disable instruction).
• Insert or re-insert an SD memory card, and execute the
function again.
• Enable the SD memory card operation, and execute the
function again.
4807H iQ Sensor
Solution related
error
• Data communications cannot be performed with a target
device of the iQ Sensor Solution data backup/restoration
function.
• Check the operation of the target device.
• Check the network status of the target device, such as a
cable, hub, and router.
• The line may be busy. Perform a retry after a while.
4808H iQ Sensor
Solution related
error
• When restoring backup data to a device supporting iQ
Sensor Solution, a device of the specified backup data and a
restoration target device do not match.
• Check and correct the specified backup data and the device
supporting iQ Sensor Solution (manufacturer, model name,
version) specified as the restoration target device.
4809H iQ Sensor
Solution related
error
• The data backup/restoration function of iQ Sensor Solution
was executed to the module which does not support the
function.
• Replace the module with the one which supports the
function.
• Execute the function to the module which supports the
function.
480AH iQ Sensor
Solution related
error
The function was executed to the CC-Link module whose
operation had been switched from the standby master station
to master station.
After powering off and on the master station and standby
master station, execute the function again.
480BH iQ Sensor
Solution related
error
The function was executed for the CC-Link module to which
"Read Model Name of Slave Station" is not set in the setting of
the automatic detection function of connected devices.
Select "Read Model Name of Slave Station" in the setting of
the automatic detection function of connected devices, and
execute the function again.
480CH iQ Sensor
Solution related
error
• The specified command cannot be executed because the
automatic detection of connected device function of iQ
Sensor Solution is being executed.
• Execute the command again after the automatic detection
processing ends.
480DH iQ Sensor
Solution related
error
• The specified command cannot be executed because the
communication setting reflection function of iQ Sensor
Solution is being executed.
• A communication timeout occurred in a command of a
device supporting iQ Sensor Solution.
• Execute the command again after the communication
setting reflection processing ends.
• Check and correct the communication time check setting
value using the engineering tool.
480EH iQ Sensor
Solution related
error
• The specified command cannot be executed because the
monitor function of iQ Sensor Solution is being executed.
• The specified command cannot be executed because the
sensor parameter read/write function of iQ Sensor Solution
is being executed.
• A communication timeout occurred in a command of a
device supporting iQ Sensor Solution.
• Execute the function again after a while.
• Execute the command again after the sensor parameter
read/write processing ends.
•
Check and correct the communication time check setting
value using the engineering tool.
480FH iQ Sensor
Solution related
error
• The iQ Sensor Solution data restoration function cannot be
executed because the CPU module cannot recognize the
system file for the iQ Sensor Solution data backup/
restoration function. (The file version differs.)
• Execute the function using the CPU module that can
recognize the system file. (Use the CPU module that can
recognize the system file version.)
4810H iQ Sensor
Solution related
error
• The restoration target module differs from the module where
the iQ Sensor Solution data backup function was executed.
• Execute the data restoration function to the module where
the data backup function was executed.
4811H iQ Sensor
Solution related
error
• The backup target module this time differs from that last
time.
• Execute the data backup function to the module where the
data backup function was executed last time.
• Set a different folder number.
4812H iQ Sensor
Solution related
error
• The functions that cannot be executed simultaneously with
the data backup/restoration function of iQ Sensor Solution,
such as the file transfer function (FTP server/client), are
being executed.
• Execute the function again after a while.
Error
code
Error name Error details and cause Action
To Next Page
Loading...
