APPX
Appendix 1 Error Codes
769
A
416AH Online
registration error
• The specified execution conditions do not exist. (Device test
with execution conditions)
• Check whether the execution conditions (program block,
step No., and execution timing) specified for disabling
settings are registered in the CPU module.
416BH Online
registration error
• Other than the ladder program was specified for the
registration of the device test with execution conditions.
• Check and correct the program block specified when the
settings of the device test with execution conditions are
registered or disabled.
41C1H File related error • The format information data of the specified drive (memory)
is abnormal.
• The file information data may be corrupted.
• Back up data in the CPU module, and then initialize the
memory.
41C2H File related error • File open specification data for file access is wrong. • Execute again after checking the specification data.
41C3H File related error • Simultaneously accessible files exceeded the maximum. • Execute again after decreasing file operations.
41C4H File related error • Simultaneously accessible files exceeded the maximum. • Execute again after decreasing file operations.
41C5H File related error • The specified file does not exist.
■When CPU Module Logging Configuration Tool is used
When an attempt was made to re-register the data logging with
the previous settings, the corresponding file did not exist.
• Execute again after checking the file.
41C7H File related error • The specified file or drive (memory) does not exist. • Execute again after checking the file or drive (memory).
41C8H File related error • The size of the specified file has exceeded that of the
existing file.
• Execute again after checking the size of the specified file.
• If the error recurs after re-execution, the file information data
may be corrupted.
• Back up data in the CPU module, and then initialize the
memory.
41C9H File related error • Access to the file sector has failed.
• The format information data of the target drive (memory) is
abnormal.
• Back up data in the CPU module, and then initialize the
memory.
41CAH File related error • Access to the file sector has failed.
• The format information data of the target drive (memory) is
abnormal.
• Back up data in the CPU module, and then initialize the
memory.
41CBH File related error • The file name is specified in a wrong method. • Execute again after checking the file name.
41CCH File related error • The specified file does not exist. Or, the specified
subdirectory does not exist.
■When CPU Module Logging Configuration Tool is used
• The data logging was started in a state that sub-folders for
storing data logging files (or folders) cannot be created or
accessed. Or, sub-folders cannot be created or accessed
while the data logging is being performed or the logged data
is being saved.
• Execute again after checking the name of the file and
subdirectory.
41CDH File related error • An access to the file is prohibited in the system.
■When CPU Module Logging Configuration Tool is used
• The data logging was started in a state that files (or folders)
cannot be created or accessed because a file (or folder) with
the same name exists. Or, files (folders) cannot be created
or accessed while the data logging is being performed or the
logged data is being saved.
• Do not access the specified file or subdirectory.
• Execute again after checking the file and subdirectory.
• Execute again after checking the open mode of the file.
41CEH File related error • The file cannot be written because the specified file is read-
only.
• Execute again after checking the attribute of the specified
file.
41CFH File related error • The specified drive (memory) has been used exceeding the
capacity.
• Execute again after checking the drive (memory) capacity.
41D0H File related error • The specified drive (memory) has no free space. Or, the
number of files in the directory of the specified drive
(memory) has exceeded the maximum.
• Execute again after increasing the free space of the drive
(memory).
• Delete files in the drive (memory), and execute the function
again.
41D1H File related error • The file name is specified in a wrong method.
• The SD memory card is being disabled by SM606 (SD
memory card forced disable instruction).
• Execute again after checking the file name.
• If the error recurs after re-execution, the file information data
may be corrupted.
• Back up data in the CPU module, and then initialize the
memory.
• Cancel the SD memory card forced disable instruction.
41D5H File related error • The file of the same name exists. • Forcibly execute the request, or execute after changing the
file name.
41D6H File related error • The format information data of the specified drive (memory)
is abnormal.
• The file information data may be corrupted.
• Back up data in the CPU module, and then initialize the
memory.
Error
code
Error name Error details and cause Action
To Next Page
Loading...
