112
4 ERROR CODE LIST
4.2 C Intelligent Function Module Dedicated Functions
-258 FEFEH ■Output signal (Y) number specification error
The value specified to the output signal (Y) number is out of
range.
Check the specified value.
-259 FEFDH ■Interrupt service routine unregistered error
The processing was not registered when enabling the
processing corresponding to an event (interrupt).
Register the processing for the event (interrupt) and perform the
operation again.
-260 FEFCH ■Memory card mount error
■Memory card unmount error
The mount processing or unmount processing of the specified
memory card failed.
•Retry.
• Check if the specified memory card is damaged.
• Replace the memory card.
-264 FEF8H ■Pointer error
The address of the specified pointer is incorrect.
Check the address of the specified pointer.
-267 FEF5H ■Authentication error
The specified password is incorrect.
Check the specified password.
-288 FEE0H ■Individual identification information read error
Reading individual identification information failed.
• Check if the C intelligent function module is running normally.
• Reset the CPU module, or turn the power OFF and ON to
reset the C intelligent function module.
-292 FEDCH ■Standard ROM shutdown error
The shutdown processing of the standard ROM failed.
• Check if files in the standard ROM are being accessed.
• Check whether all files in the standard ROM have been
closed.
-320 FEC0H ■Clock rate specification error
The specified clock rate is out of range.
Check the specified clock rate.
-328 FEB8H ■Maximum setting size exceeded error
The setting size of data sampling in each sequence scan is out
of range.
Check the maximum setting size of data sampling in each
sequence scan.
-329 FEB7H ■Setting data error
The setting data of data sampling in each sequence scan is
incorrect.
• Check the setting data of data sampling in each sequence
scan.
• Set target data within the range in which devices of the control
CPU are assigned.
• Review the device type.
• Review the number of blocks.
• Review the number of retainable records.
-330 FEB6H ■Data sampling setting error
The data to be sampled was set during data sampling in each
sequence scan.
Stop data sampling in each sequence scan, and set data to be
sampled again.
-331 FEB5H ■Sampling setting unregistered error
Acquisition of sampled data failed because data sampling in
each sequence scan was not set.
Check if data sampling in each sequence scan is set.
-332 FEB4H ■Sampling setting unregistered error
Starting sampling failed because data sampling in each
sequence scan was not set.
Check if data sampling in each sequence scan is set.
-333 FEB3H ■Memory reservation error
Reserving memory for the number of retainable records for data
sampling in each sequence scan failed.
Check the number of retainable records.
-334 FEB2H ■Number of retainable records exceeded error
The number of wait records exceeds the number of retainable
records that is set in the data sampling in each sequence scan
setting.
Check the number of wait records.
-335 FEB1H ■F
unction unsupported error
The control CPU does not support the sequence scan
synchronization sampling function.
Replace the control CPU with a CPU module supporting the
sequence scan synchronization sampling function (high speed
sampling).
-336 FEB0H ■Maximum number of settings error
The total number of device points of each module using the
sequence scan synchronization sampling function of the control
CPU exceeds the maximum number of points.
When multiple modules use the sequence scan synchronization
sampling function, review the setting so that the total number of
sampling device points of each module is the maximum number
of points or less of the control CPU.
-337 FEAFH ■Maximum number of settings error
The number of modules using the sequence scan
synchronization sampling function of the control CPU exceeds
the maximum number.
Configure a system so that the number of modules using the
sequence scan synchronization sampling function of the control
CPU does not exceed the maximum number.
-338 FEAEH ■Sampling wait error
A request was received in the state where the module could not
wait for data sampling in each sequence scan.
Perform it again after starting data sampling in each sequence
scan.
Error code Description Corrective action
Decimal Hexadec
imal
To Next Page
Loading...
