Mitsubishi Electric Q62DAN - Page 52

3 - 25 3 - 25
MELSEC-Q
3 SPECIFICATIONS
Table 3.9 Buffer memory assignment (Q68DAVN/Q68DAV) (2/2)
Address
Description
Default
1
Read/write
2
Reference
section
Hexadecimal Decimal
19H 25
System area — — —
to to
9DH 157
9EH 158
Mode switching setting
0 R/W
Section 3.4.12
9FH 159 0 R/W
A0H 160
System area — — —
to to
C9H 201
CAH 202
CH1 Industrial shipment settings offset value
3
0 R/W
Section 3.4.14
CBH 203 CH1 Industrial shipment settings gain value
3
0 R/W
CCH 204
CH2 Industrial shipment settings offset value
3
0 R/W
CDH 205 CH2 Industrial shipment settings gain value
3
0 R/W
CEH 206 CH3 Industrial shipment settings offset value
3
0 R/W
CFH 207
CH3 Industrial shipment settings gain value
3
0 R/W
D0H 208 CH4 Industrial shipment settings offset value
3
0 R/W
D1H 209
CH4 Industrial shipment settings gain value
3
0 R/W
D2H 210 CH5 Industrial shipment settings offset value
3
0 R/W
D3H 211 CH5 Industrial shipment settings gain value
3
0 R/W
D4H 212 CH6 Industrial shipment settings offset value
3
0 R/W
D5H 213 CH6 Industrial shipment settings gain value
3
0 R/W
D6H 214
CH7 Industrial shipment settings offset value
3
0 R/W
D7H 215 CH7 Industrial shipment settings gain value
3
0 R/W
D8H 216 CH8 Industrial shipment settings offset value
3
0 R/W
D9H 217 CH8 Industrial shipment settings gain value
3
0 R/W
DAH 218 CH1 User range settings offset value
3
0 R/W
DBH 219
CH1 User range settings gain value
3
0 R/W
DCH 220 CH2 User range settings offset value
3
0 R/W
DDH 221
CH2 User range settings gain value
3
0 R/W
DEH 222 CH3 User range settings offset value
3
0 R/W
DFH 223 CH3 User range settings gain value
3
0 R/W
E0H 224
CH4 User range settings offset value
3
0 R/W
E1H 225 CH4 User range settings gain value
3
0 R/W
E2H 226
CH5 User range settings offset value
3
0 R/W
E3H 227 CH5 User range settings gain value
3
0 R/W
E4H 228 CH6 User range settings offset value
3
0 R/W
E5H 229
CH6 User range settings gain value
3
0 R/W
E6H 230 CH7 User range settings offset value
3
0 R/W
E7H 231
CH7 User range settings gain value
3
0 R/W
E8H 232 CH8 User range settings offset value
3
0 R/W
E9H 233 CH8 User range settings gain value
3
0 R/W
1 This is the initial value set after the power is turned on or the programmable controller CPU is reset.
2 Indicates whether reading from and writing to a sequence program are enabled.
R : Reading enabled W : Writing enabled
3 Areas used to restore the user range settings offset/gain values when Online module change is made.
Refer to chapter 7 for details of Online module change.