Mitsubishi Electric Q62DAN - Page 54

3 - 27 3 - 27
MELSEC-Q
3 SPECIFICATIONS
Table 3.10 Buffer memory assignment (Q68DAIN/Q68DAI) (2/2)
Address
Description Default
1
Read/write
2
Reference
section
Hexadecimal Decimal
19H 25
System area — — —
to to
9DH 157
9EH 158
Mode switching setting
0 R/W
Section 3.4.12
9FH 159 0 R/W
A0H 160
System area — — —
to to
C9H 201
CAH 202 CH1 Industrial shipment settings offset value
3
0 R/W
Section 3.4.14
CBH 203 CH1 Industrial shipment settings gain value
3
0 R/W
CCH 204 CH2 Industrial shipment settings offset value
3
0 R/W
CDH 205 CH2 Industrial shipment settings gain value
3
0 R/W
CEH 206
CH3 Industrial shipment settings offset value
3
0 R/W
CFH 207 CH3 Industrial shipment settings gain value
3
0 R/W
D0H 208 CH4 Industrial shipment settings offset value
3
0 R/W
D1H 209 CH4 Industrial shipment settings gain value
3
0 R/W
D2H 210 CH5 Industrial shipment settings offset value
3
0 R/W
D3H 211
CH5 Industrial shipment settings gain value
3
0 R/W
D4H 212 CH6 Industrial shipment settings offset value
3
0 R/W
D5H 213
CH6 Industrial shipment settings gain value
3
0 R/W
D6H 214 CH7 Industrial shipment settings offset value
3
0 R/W
D7H 215 CH7 Industrial shipment settings gain value
3
0 R/W
D8H 216
CH8 Industrial shipment settings offset value
3
0 R/W
D9H 217 CH8 Industrial shipment settings gain value
3
0 R/W
DAH 218
CH1 User range settings offset value
3
0 R/W
DBH 219 CH1 User range settings gain value
3
0 R/W
DCH 220 CH2 User range settings offset value
3
0 R/W
DDH 221
CH2 User range settings gain value
3
0 R/W
DEH 222 CH3 User range settings offset value
3
0 R/W
DFH 223
CH3 User range settings gain value
3
0 R/W
E0H 224 CH4 User range settings offset value
3
0 R/W
E1H 225 CH4 User range settings gain value
3
0 R/W
E2H 226 CH5 User range settings offset value
3
0 R/W
E3H 227 CH5 User range settings gain value
3
0 R/W
E4H 228
CH6 User range settings offset value
3
0 R/W
E5H 229 CH6 User range settings gain value
3
0 R/W
E6H 230 CH7 User range settings offset value
3
0 R/W
E7H 231 CH7 User range settings gain value
3
0 R/W
E8H 232 CH8 User range settings offset value
3
0 R/W
E9H 233
CH8 User range settings gain value
3
0 R/W
1 This is the initial value set after the power is turned on or the programmable controller CPU is reset.
2 Indicates whether reading from and writing to a sequence program are enabled.
R : Reading enabled W : Writing enabled
3 Areas used to restore the user range settings offset/gain values when Online module change is made.
Refer to chapter 7 for details of Online module change.