Mitsubishi Electric RD62P2E - Index

84
INDEX
0 to 9
1-phase multiple of 1 . . . . . . . . . . . . . . . . . . . . . 13
1-phase multiple of 2 . . . . . . . . . . . . . . . . . . . . . 13
2-phase multiple of 1 . . . . . . . . . . . . . . . . . . . . . 14
2-phase multiple of 2 . . . . . . . . . . . . . . . . . . . . . 14
2-phase multiple of 4 . . . . . . . . . . . . . . . . . . . . . 14
A
Application setting. . . . . . . . . . . . . . . . . . . . . . . 41
B
Basic setting. . . . . . . . . . . . . . . . . . . . . . . . . . . 39
C
CH1 Coincidence output point No.1 setting . . . . . 62
CH1 Coincidence output point No.2 setting . . . . . 62
CH1 Coincidence signal enable command. . . . . . 58
CH1 Coincidence signal No.1 reset command . . . 57
CH1 Coincidence signal No.2 reset command . . . 59
CH1 Count enable command . . . . . . . . . . . . . . . 58
CH1 Counter function selection setting . . . . . . . . 63
CH1 Counter function selection start command . . 59
CH1 Counter function update flag . . . . . . . . . . . . 66
CH1 Counter value coincident (point No.1) . . . . . 55
CH1 Counter value coincident (point No.2) . . . . . 56
CH1 Counter value larger (point No.1). . . . . . . . . 55
CH1 Counter value larger (point No.2). . . . . . . . . 56
CH1 Counter value smaller (point No.1) . . . . . . . 56
CH1 Counter value smaller (point No.2) . . . . . . . 57
CH1 Cycle pulse count current value. . . . . . . . . . 65
CH1 Cycle pulse count difference value . . . . . . . 65
CH1 Cycle pulse count previous value . . . . . . . . 64
CH1 Down count command . . . . . . . . . . . . . . . . 58
CH1 External preset detection reset command. . . 58
CH1 External preset request detection . . . . . . . . 56
CH1 Latch count value . . . . . . . . . . . . . . . . . . . 64
CH1 Measured pulse value . . . . . . . . . . . . . . . . 68
CH1 Measured pulse value update flag . . . . . . . . 68
CH1 Overflow detection . . . . . . . . . . . . . . . . . . . 63
CH1 Present value . . . . . . . . . . . . . . . . . . . . . . 62
CH1 Preset command . . . . . . . . . . . . . . . . . . . . 57
CH1 Preset value setting . . . . . . . . . . . . . . . . . . 62
CH1 Pulse measurement section setting . . . . . . . 67
CH1 Pulse measurement start command
(pulse measurement)
. . . . . . . . . . . . . . . . . . . . . 59
CH1 Pulse under-measurement flag . . . . . . . . . . 68
CH1 PWM output cycle time setting . . . . . . . . . . 67
CH1 PWM output ON time setting 1 . . . . . . . . . . 67
CH1 PWM output ON time setting 2 . . . . . . . . . . 67
CH1 PWM output start command (PWM output). . 59
CH1 Ring counter lower limit value setting . . . . . . 65
CH1 Ring counter upper limit value setting . . . . . 65
CH1 Sampling count value. . . . . . . . . . . . . . . . . 64
CH1 Sampling/cycle counter flag . . . . . . . . . . . . 64
CH1 Sampling/cycle time setting. . . . . . . . . . . . . 63
CH1 Signal monitor . . . . . . . . . . . . . . . . . . . . . . 66
CH1 Synchronization latch count value . . . . . . . . 67
CH1 Synchronization measured pulse value . . . . 68
Coincidence detection interrupt function . . . . . . . .23
Coincidence output function. . . . . . . . . . . . . . . . . 20
Count disable function. . . . . . . . . . . . . . . . . . . . .28
Count error . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Counter function selection . . . . . . . . . . . . . . . . . . 26
Counter type . . . . . . . . . . . . . . . . . . . . . . . . . . .17
CW/CCW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Cycle pulse counter function . . . . . . . . . . . . . . . . 31
I
Interrupt setting . . . . . . . . . . . . . . . . . . . . . . . . .42
L
Latch counter function. . . . . . . . . . . . . . . . . . . . .29
Linear counter function . . . . . . . . . . . . . . . . . . . .17
M
Module label . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Module ready . . . . . . . . . . . . . . . . . . . . . . . . . . .55
O
Overflow error . . . . . . . . . . . . . . . . . . . . . . . . . .17
P
Parameter settings . . . . . . . . . . . . . . . . . . . . . . . 39
Performing the preset function using a program . . .24
Performing the preset function using an external control
signal
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Preset function . . . . . . . . . . . . . . . . . . . . . . . 24,46
Pulse measurement function . . . . . . . . . . . . . . . .34
PWM output function. . . . . . . . . . . . . . . . . . . . . .36
R
Reading the present value. . . . . . . . . . . . . . . . . .16
Refresh processing time . . . . . . . . . . . . . . . . . . .45
Refresh setting. . . . . . . . . . . . . . . . . . . . . . . . . . 43
Ring counter function . . . . . . . . . . . . . . . . . . . . . 18
S
Sampling counter function . . . . . . . . . . . . . . . . . . 30