Mitsubishi SRK25ZSP-W User Manual

'18 • SRK-SM-259
-
15
-
(p) Rotor lock
(q) Outdoor fan motor protection
(r) Outdoor fan control at low outdoor temperature
Cooling
1) Operating conditions
(s) Refrigeration cycle system protection
(i) Starting conditions
2) Detail of operation
3) Reset conditions
Heating
1) Operating conditions
2) Detail of operation
3) Reset conditions
Outdoor temperature > 10˚C
Outdoor temperature
<
=
10˚C
Outdoor fan
a)
b)
a)
b)
a)
b)
1)
2)
c)
When 5 minutes have elapsed after the compressor ON or the completion of the defrost operation
Other than the defrost operation
3)
When, after satisfying the conditions of 1) and 2) above, the compressor speed, indoor air temperature (Th1) and indoor
heat exchanger temperature (Th2) have satisfied the conditions in the following table for 10 (SRK45:5) minutes:
Compressor speed (N)Operation mode
Cooling
Heating(1)
Indoor air temperature (Th1)
Th1−4<Th2
Room temperature (Th1)/
Indoor heat exchanger temperature (Th2)
Th2<Th1+6
50 N
<
=
10 Th1 40
<
=
<
=
0 Th1 40
<
=
<
=
50 N
<
=
(i)
(ii)
Except that the fan speed is HI in heating operation.
Values in ( ) are for the model SRK35.
(model SRK45:0 )
min
-1
-
-
(model SRK45:2 )
; models SRK25, 35 : refer to belows,
model SRK45 : 8th speed)
Th1 < 21℃
SRK25, 35
8th speed
9th(8th) speed
Th1
21℃
8th speed
8th speed
ON1
ON2
>
=
-1 1 4 6
Outdoor air temperature(°C )
ON1
ON2
OFF
24
(p) Rotor lock
(q) Outdoor fan motor protection
(r) Outdoor fan control at low outdoor temperature
Cooling
1) Operating conditions
(s) Refrigeration cycle system protection
(i) Starting conditions
2) Detail of operation
3) Reset conditions
Heating
1) Operating conditions
2) Detail of operation
3) Reset conditions
Outdoor temperature > 10˚C
Outdoor temperature
<
=
10˚C
Outdoor fan
a)
b)
a)
b)
a)
b)
1)
2)
c)
When 5 minutes have elapsed after the compressor ON or the completion of the defrost operation
Other than the defrost operation
3)
When, after satisfying the conditions of 1) and 2) above, the compressor speed, indoor air temperature (Th1) and indoor
heat exchanger temperature (Th2) have satisfied the conditions in the following table for 10 (SRK45:5) minutes:
Compressor speed (N)Operation mode
Cooling
Heating(1)
Indoor air temperature (Th1)
Th1−4<Th2
Room temperature (Th1)/
Indoor heat exchanger temperature (Th2)
Th2<Th1+6
50 N
<
=
10 Th1 40
<
=
<
=
0 Th1 40
<
=
<
=
50 N
<
=
(i)
(ii)
Except that the fan speed is HI in heating operation.
Values in ( ) are for the model SRK35.
(model SRK45:0 )
min
-1
-
-
(model SRK45:2 )
; models SRK25, 35 : refer to belows,
model SRK45 : 8th speed)
Th1 < 21℃
SRK25, 35
8th speed
9th(8th) speed
Th1
21℃
8th speed
8th speed
ON1
ON2
>
=
-1 1 4 6
Outdoor air temperature(°C )
ON1
ON2
OFF
24
(ii) Contents of control
1)
(iii) Reset condition
When the compressor has been turned OFF.
2)
When the conditions of (i) above are satisfied, the compressor stops.
Error stop occurs when the compressor has stopped 3 times within 60 minutes.

Mitsubishi SRK25ZSP-W Specifications

General

Brand	Mitsubishi
Model	SRK25ZSP-W
Category	Air Conditioner
Language	English