To Next PageTo Next PageHow to fix Mizuho osi 5803 Accessories when no column function either end?
If the Mizuho osi Accessories column function is not working at either end, ensure the device is plugged in and turned on. Try resetting the breaker. Also, check the connector to make sure it is properly plugged in.
What to do if rotation friction control won’t stop rotation on Mizuho osi 5803 Accessories?
If the rotation friction control on your Mizuho osi Accessories won’t stop rotation at either the head or foot end, you should try the following: 1. Adjust the brake tension. 2. Adjust the handle to the proper range. 3. Replace the component if the problem persists.
What to do if there is no column function at the foot end of Mizuho osi 5803 Accessories?
If the Mizuho osi Accessories column function is not working at the foot end, ensure that the connector is properly plugged in.
General| Brand | Mizuho osi |
|---|---|
| Model | 5803 |
| Category | Accessories |
| Language | English |
General caution for safe operation and reference.
Indicates important instructions and guidelines for electrical safety.
Warnings regarding procedures, patient care, and table top gimbal compatibility.
Describes the 5803 Advanced Control I-Base and its purpose.
Lists technical specifications like weight, height, tilt, and power input.
Guidelines for shipping and storing the 5803 Base to prevent damage.
Procedures for receiving, accepting, and inspecting the table.
Identifies major components via side, head end, and foot end views.
Defines orientation and location of model/serial number label.
Details on locking and unlocking the base casters.
Explains the functions of the hand pendant for table manipulation.
Interpretation of battery/fault lights and hand control connection.
Overview of indicator lights on the head end base and pivot assembly.
Function and operation of the rotation safety lock switch.
Explains the 180° rotation lock indicator light and lever operation.
Describes the tilt drive status indicator light and its synchronization.
Procedure for synchronizing the lateral tilt drive and crossbars.
Steps for re-synchronizing tilt drive based on table top attachment.
How to couple modular table tops to the 5803 Advanced Control Base.
Step-by-step guide for installing H-frames to columns and crossbars.
Checks for coupling, patient transfer, and second top attachment.
Procedures for patient rotation and the automatic rotation lock system.
Step-by-step guide for performing a 180° patient rotation.
Instructions for retracting the base to its minimum length for storage.
Procedure for storing a table top on a collapsed base.
Procedures for cleaning and disinfecting the 5803 Advanced Control Base.
Guidance on lubricating the base's internal and external components.
Information on obtaining a preventative maintenance checklist.
Details on power cord, ON/OFF switch, and status lights.
How batteries are charged and status indicators for recharging.
Troubleshooting steps for electrical system malfunctions.
Guide correlating commands, results, and potential issues.
Steps for removing and replacing the head end cover.
Steps for removing and replacing the foot end cover.
Procedure for disconnecting and removing the hand pendant module.
Warnings and precautions for handling and replacing batteries.
Battery placement, removal, and replacement procedures.
Procedures for replacing power supply and controller circuit board.
Steps for replacing power switch, head end assembly, and tilt motor.
Procedure for removing and replacing the foot end rotation safety lock motor.
Procedures for replacing head/foot columns and the retractable center beam.
Procedure for removing and replacing casters.
Procedure for adjusting the tilt actuator rod end position for clearance.
Steps for setting and adjusting the 180° rotation lock sensor.
Procedure for adjusting the home and tilt left/right sensor switches.
Procedure for adjusting the head end slider for proper movement friction.
Adjustment procedure for the rotation safety lock as it wears.
Steps to set the rotation safety lock (brake) ON sensor.
Contact details for service, parts, and instant support package.
Procedures for ordering replacement parts and returning damaged parts.
Procedures for sending parts for repair and EC authorized representative contact.
List of replacement and spare parts for the 5803 Modular Base.
Visual catalog of common replacement parts with part numbers.
Electrical schematic showing component interconnections.
