Why is my component not receiving power from Monster Power Power Strip?
If your component isn't receiving power from the Monster Power Power Strip, there might be a few reasons. First, ensure the Power Strip is turned on. If that doesn't work, try plugging the component into an unswitched outlet. Also, if the Power Strip is plugged into a switched outlet, make sure the component's power is turned on as well.
Why is my Monster Power Power Strip not receiving power?
If your Monster Power Power Strip is not receiving power, first ensure that the Power Strip switch is turned on. Also, verify that the Power Strip’s AC power plug is properly plugged into a grounded 120 volts (nominal) wall outlet. In some homes, the wall plug may be controlled by a wall switch, so try turning on nearby light switches.
What to do if my Monster Power PowerCenter HTS3600MKII Power Strip trips the circuit breaker?
If too many devices are connected to your Monster Power Power Strip, it can cause an overload, tripping the Thermal Circuit Breaker. To resolve this, press the Power Strip Thermal Circuit Breaker button to reset it, and allow 10 minutes before attempting to reset. If the Circuit Breaker continues to trip, try moving one or more components to another Power Strip.
What to do if my Monster Power Power Strip is emitting a loud buzzing alarm?
If your Monster Power Power Strip is emitting a loud buzzing alarm, it means that the internal protection circuitry has sacrificed itself to protect your connected equipment from a catastrophic surge. In this case, the Power Strip must be replaced. Refer to the Warranty Information section for details.
Why do my speakers emit a humming noise from Monster Power Power Strip?
If your speakers are emitting a humming or buzzing noise when connected to the Monster Power Power Strip, it could be due to the Power Strip sharing AC power with equipment that isn't properly grounded. Try connecting your Power Strip to a dedicated outlet. You can also try unplugging components one at a time to see if the noise stops. If a component is improperly grounded, attach a copper wire from its chassis to the Power Strip’s grounding post.
What to do if the Unswitched LED is off on my Monster Power PowerCenter HTS3600MKII Power Strip?
If the Unswitched LED on the front panel of your Monster Power Power Strip is off, there are a few potential causes. First, make sure the Power Strip is plugged into a properly grounded 120 volts (nominal) outlet and that the outlet is on. If you're using the Switched Outlet Remote Turn-On feature, ensure the plug is connected to the component you want to use for activation. Also, check the battery in the component's remote control.
Why is the “Timed On” indicator off on my Monster Power PowerCenter HTS3600MKII Power Strip?
If the “Timed On” indicator on the front panel of your Monster Power Power Strip is off, and you're using the Remote Turn-On feature, ensure the plug is connected to the component you wish to use for activation. Also, check the battery in the component's remote control. Finally, make sure the component you're using to activate the Remote Turn-On is plugged into a properly grounded 120 volt outlet.
General| Brand | Monster Power |
|---|---|
| Model | PowerCenter HTS3600MKII |
| Category | Power Strip |
| Language | English |
Warning about using correct power outlets and consulting electricians if unsure.
Instructions on proper plug use, grounding, and avoiding adapters.
Caution against operating unit if liquid is spilled or near water.
Advice on routing cords to prevent hazards and damage.
Recommendation to disconnect unit during lightning storms for protection.
Warning against opening the unit for repairs; consult manual.
Avoid placing unit in direct sunlight or near heat sources.
Only use light dusting; avoid liquids or aerosol cleaners.
Emphasizes the need for a properly grounded outlet for safety and equipment protection.
States that all cables must connect to the PowerCenter for surge protection.
Explains warranty invalidity if components are not properly protected.
Confirms surge protection circuitry is functioning properly.
Shows power is supplied to the unswitched outlets.
Indicates power is supplied to the switched outlets.
Shows power is supplied to sequentially timed outlets.
Alerts if line/neutral wires are reversed from the wall outlet.
Confirms the unit is plugged into a grounded outlet.
Confirms Monster Clean Power circuitry is active.
Alerts to voltage outside the safe operating range (below 70V or above 130V AC).
Displays the input voltage and amperage draw of the unit.
Adjusts the brightness of the digital meter display.
Activates programmed "Switched On" or "Switched On After Delay" outlets.
Deactivates programmed "Switched On" or "Switched On After Delay" outlets.
Outlets with filters reducing interference for digital components.
Outlets with filters reducing interference for video components.
Outlets with filters reducing interference for audio components.
Outlets for high-power components like amplifiers.
Surge protection for TV/cable connections.
Surge protection for satellite dish connections.
Surge protection for antenna connections.
Allows automatic turn-on via an AC trigger from another component.
Allows automatic turn-on via a DC trigger from another component.
Allows automatic turn-on of other components via DC trigger.
Protects against continuous power overload.
Surge protection for telephone line connections.
High-density, double-shielded power cord for optimal power transfer.
Provides a ground reference point for ungrounded components.
Connect digital components to filtered digital outlets for best performance.
Connect video components to filtered video outlets for optimal performance.
Connect analog audio components to filtered analog audio outlets.
Connect high-power audio components like amplifiers to appropriate outlets.
Connect coaxial cables for TV/Cable, Satellite, and Antenna for surge protection.
Connect phone lines for surge protection and utilize the built-in splitter.
Connect for automatic turn-on/off via a DC trigger from another component.
Connect for automatic turn-on/off via an AC trigger from another component.
Instructions for attaching rack ears for installation in an equipment rack.
Addresses issues where the unit is not powering on or receiving power.
Troubleshoots components failing to power on from the unit.
Diagnoses and resolves audio noise issues related to grounding.
Checks why the unswitched power indicator light is not illuminated.
Troubleshoots why the switched power indicator light is not illuminated.
Addresses the 'Timed On' indicator not functioning as expected.
Resolves problems like rolling bars or ghosting in the video signal.
Explains the unit emitting a loud buzzing alarm, indicating protection circuitry activation.
Explains key terms used within the warranty document.
Details coverage for product defects and connected equipment damage.
Specifies governing law and legal jurisdiction for disputes.
Outlines additional legal rights granted to the consumer.
Instructions and importance of registering the product.
Step-by-step instructions for submitting a warranty claim.
Describes the process after a claim is submitted, including repair estimates.
Details the expected timeframe for resolving warranty claims.
To Next Page
