Need help?Do you have a question about the Moving Terrain MT-VisionAir X ETSO and is the answer not in the manual?
General| Brand | Moving Terrain |
|---|---|
| Model | MT-VisionAir X ETSO |
| Category | Avionics Display |
| Language | English |
Strictly avoid using both central connectors simultaneously; ensure adequate ventilation to prevent overheating.
Describes the device as a panel-mounted or handheld unit for flight planning and operation.
Illustrates the device from various angles and provides detailed dimensions.
Explains the meaning of labels and the serial numbering system on the device.
Details the mandatory display position for the warning sign in the cockpit.
Guidance on choosing the best location and installing the Easy mount in the cockpit panel.
Provides specifications for panel cutout and dimensions for mounting the Easy mount.
Important notes regarding vibration, locking mechanisms, and cable management during installation.
Discusses alternative mounting locations and the need for special devices.
Recommends installation on glare shield, discusses visibility, cable length, and ground plate.
Specifies minimum distance requirements between GPS and satellite antennas to avoid interference.
Details recommended power sources, required fuses, and battery pack usage.
Provides an overview of device connections, including USB, Ethernet, and central connectors.
Detailed pin assignments for the 50-pin MDR connector and cable assembly guidelines.
Explains test cabling, further device connections, and GPS configuration in the software.
Covers crossfilling data from Garmin devices and transmitting user routes via USB.
Describes how to adjust the screen's brightness using the star button.
How to check system version, update software, charts, and data using a USB stick.
Step-by-step guide for upgrading the device's operating system via USB.
Procedures for backing up and restoring user data, and handling related error messages.
Instructions on how to access and edit the mtpro.ini configuration file.
Lists required hardware and software for MT Satellite Radar and MT BlitzPlan.
Details on connecting satellite phones (Thuraya, Iridium) and UMTS modems.
Explains datalink capabilities, status infoblocks, and communication loss scenarios.
Guides for downloading radar data for MT Satellite Radar (standard and enhanced).
Steps for testing the MT BlitzPlan connection and flightplan archiving.
Covers system components, antenna installation, and connection for Avidyne TAS600.
Details on connecting and configuring the PowerFLARM interface for traffic awareness.
Instructions for the parallel use of Avidyne TAS and PowerFLARM interfaces.
Information on connecting and configuring the Garrecht TRX1090 ADS-B receiver.
Lists required components and explains the connection setup for MT Stormscope.
Details the MT-VGA-Output Device and its USB connection to the MT-VisionAir X.
Advice for using MT-Video-Input and MT-VGA-Output devices together.
Describes the MT Camera device, its signals, and display capabilities.
How to use the hotkey 'C' and adapt parameters in mtpro.ini for the MT-Camera.
Details the MT-VGA-Input Device, its connection to MT-VisionAir X, and prerequisites.
Illustrates connection setup and suggests modification of the Easy Mount for cable routing.
Explains how external dimming mode is activated and its wiring via the central connector.
Lists requirements for using the MT-MMS, including Iridium Satphone and SBD contract.
Describes how to activate aircraft tracking, set intervals, and interpret status messages.
Details normal operation messages and common/uncommon error conditions for MMS.
Lists hardware, software, and contracts needed for Rescue Track via ITAS.
Explains how to configure the ITAS module using mtpro.ini and system settings.
Describes the Rescue Track MMS screen layout and how to select/send messages.
Provides technical information and installation advice for the ITAS test cable and module.
Checklist for verifying the correct installation of the unit and its basic functions.
Checklist for verifying satellite telephone antenna, connection, and data reception.
Verifies UMTS telephone source selection and checks various COM port connections.
Detailed technical specifications for the MT-Vision Air X ETSO system.
Technical details for the Fast Integral GPS receiver, including frequency and dimensions.
Table detailing the assignment of COM ports for various signals and devices.
To Next Page